Defender-Sam said:
Made a start on my wheel carrier,

IMG_0213.jpg


IMG_0214.jpg


IMG_0216.jpg


IMG_0228.jpg


IMG_0229.jpg


Sam
Click to expand...

Looking good. Is it gonna open when the door opens? If so do you need any close up pics of the linkage & adjuster??
 
redhand said:
Looking good. Is it gonna open when the door opens? If so do you need any close up pics of the linkage & adjuster??
Click to expand...

cheers redhand yes that the plan, but still need to work out how I've looked at plenty of pics and have come to the conclusion that the linkage/mechanism depends on where the hinges are located. so if yours are like mine (close to the door hinges) then some pics would be great. ;)
 
Went to go change the shock bushes for MOT on the dwarfs series only to find out the rear bottom shocks are mounted with split pins…..

They look ####ed and I don't have replacements so have left it for now, the drivers side one is also mounted in the opposite direction to the passenger one
 
mines right up against the edge of the tub.

so will take some pics when it stops raining.
 
Replaced my rear hub bearings and seal's.

Also discovered a major vibration coming from front area, think the front left. Found out it only happens when the fwh's are engaged so believe it's the uj's passed it.
 
spent 3 hours jet washing the out side. cut all the sound proofing and carpets out and jetted the inside to find out i have a major rot problem. so next job is to get the welder out. oh and put the top window back in witch poped out when i fell in a ditch lol.
 
hullhunter said:
spent 3 hours jet washing the out side. cut all the sound proofing and carpets out and jetted the inside to find out i have a major rot problem. so next job is to get the welder out. oh and put the top window back in witch poped out when i fell in a ditch lol.
Click to expand...

That sound proofing is like a sponge. . Terible design. Dont forget to take photos:D
 
dr_evil said:
went to go change the shock bushes for mot on the dwarfs series only to find out the rear bottom shocks are mounted with split pins…..

They look ####ed and i don't have replacements so have left it for now, the drivers side one is also mounted in the opposite direction to the passenger one
Click to expand...

😱
 
That's coming along nicely. That bottom arm takes a lot of strain and stress You might want to think about adding a gusset (OOERR Missus) plate, across that weld. Where the 2 lower tubes meet.
 
redhand said:
That's coming along nicely. That bottom arm takes a lot of strain and stress You might want to think about adding a gusset (OOERR Missus) plate, across that weld. Where the 2 lower tubes meet.
Click to expand...

thanks, yes not a bad idea that one (you mean the second pic) where the angled piece joint the horizontal bottom bar.... just wondering whether i could make a tube piece or some plate cut at an angle. :confused2:
 
NOWT!! Bloody rain!!

Did find out I wasn't out of CO2 just my regulator decided to break internally. New pin made fitted and tested but no welding done!

Roll on tomorrow!
 
redhand said:
That's coming along nicely. That bottom arm takes a lot of strain and stress You might want to think about adding a gusset (OOERR Missus) plate, across that weld. Where the 2 lower tubes meet.
Click to expand...

i seccond this, that is a definate week point, but looks brilliant!
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
472
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
575
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
839
Knappster
Knappster
Mooky
Replacing thermostat
Replies
8
Views
249
Forrest Gump
F
I
Re-coding of ABS Module after repacement
Replies
10
Views
922
invisible999
I