first lane of the day
guess you are'nt up for that 1 if ya come down again ?
No point in damaging the motor unnecessarily.
its just good to get out for the day - good food, good mates and good views. suites me, sir.
No point in damaging the motor unnecessarily.
its just good to get out for the day - good food, good mates and good views. suites me, sir.
buckshot
Well-Known Member
No point in damaging the motor unnecessarily.
its just good to get out for the day - good food, good mates and good views. suites me, sir.
the ones we did today can be incorperated into the lot you did with us, think we now have enough to make up a days "soft" laning and a "hardcore" version too.
Scruffyhippo
New Member
Welding up the rear crossmember and fitting new chassis mounts !
Sirus
Your all Banned except me
should see the fookin tree though
must get going on knocking up the front hoop and roof bars
I thinks its you that should have seen the tree:doh::doh::doh::doh:
Muddy Gonzo
Banned
Gave the old bitch a bath today and painted some of the underside.
bustersbus
Well-Known Member
Renewed me power steerin' pump.. just to finish bleedin' it through properly as ran out of ATF:doh:
timberjock
Active Member
jist finished painting replacement bulkhead and working oot how 300tdi wiring fits 200tdi wiring. So jist got to start strippin down the 90 to get its bulkhead oot.
Co-Pang-Yang
Well-Known Member
Nothing today as i was busy spreading 20t of used tarmac over the drive.
Using it to go get a wacker from KB's tomorrow though.
Still not sorted the leaking transfer box or re-attached the front prop yet, bad times.
Using it to go get a wacker from KB's tomorrow though.
Still not sorted the leaking transfer box or re-attached the front prop yet, bad times.
bustersbus
Well-Known Member
Got some ATF and bled me steerin' through
G-man
BBQ king
isn't there standard measurements for the rods? (between the centres of the rod ends) so yer make ther drag link XX inches long and yer steering arm XX inches long and bingo roberts yer mothers brother
j the range
New Member
just been and picked up wheel and tyer, i won on ebay. well happy..
![[JP]](/data/avatars/m/29/29578.jpg?1437394565){kind=avatar}
[JP]
New Member
Well, since I sold my Disco and got back from hols, I've been doing bits and bobs on the Defender to get it ready for the winter muddy season..
So far I've washed all the mud from inside, front and back and booked it in for a steam clean underneath..
other than that i've been playing around with chequer plate, fit my snorkel and straight through exhaust..
the chequer plate I did it the other day..
then repaired a little hole on the right chassi leg
then was time to play with the snorkel..
found a way of fitting it in with straight route for air intake and exit..
then welded a plate on the water drain nipple
then after trying a few times for placemente, I've holded the air hoses in place with jubilee clips and then sealed around
then finally, the postman delivered this shinny bit for me, so it was out with the old and in with the new...
the back box is out too...and tomorrow I shall cut it off and weld some pipe together..
busy, busy!!
So far I've washed all the mud from inside, front and back and booked it in for a steam clean underneath..
other than that i've been playing around with chequer plate, fit my snorkel and straight through exhaust..
the chequer plate I did it the other day..
then repaired a little hole on the right chassi leg
then was time to play with the snorkel..
found a way of fitting it in with straight route for air intake and exit..
then welded a plate on the water drain nipple
then after trying a few times for placemente, I've holded the air hoses in place with jubilee clips and then sealed around
then finally, the postman delivered this shinny bit for me, so it was out with the old and in with the new...
the back box is out too...and tomorrow I shall cut it off and weld some pipe together..
busy, busy!!
