Undone the drivers side engine mount and....

Picture011Medium.jpg


Wait for all the oil to come out and have lunch atm
 
gemsdad said:
i hope no one from the forum is waiting to bid on your car mate,:p;)
Click to expand...

Shoosh you. It actually looks fantastic. It's in better condition than when i bought it. Cruise control's working now too. Replaced the hoses and jobs a good un. Must have been a split i couldnt see :)
 
:mad: :mad:

After changing the hoses, the CC worked for a while, then it stopped :mad:

So, took the whole lot apart, everythings connected ok, no dodgy connections :mad:

Has the vac unit been known to be dodgy at all?
 
hammy2909 said:
:mad: :mad:

After changing the hoses, the CC worked for a while, then it stopped :mad:

So, took the whole lot apart, everythings connected ok, no dodgy connections :mad:

Has the vac unit been known to be dodgy at all?
Click to expand...

only in yours hammy.:eek::behindsofa::bolt:
 
I havent done anything to it....
but ordered gear and transfer box breathers and timing belt cover breather... as the cold water hiting the timing case, even with the wading plug in, sucks water, so with the breather if it wants to suck anything it will be air up near the snorkel...!!!
 
cleaned it out , washed it took pics ,which didnt turn out, if its not sold by 2nd week in september it goes to the scrap man.
 
took off the rear hub as it was ****in out grease after 500 miles expecting yet another bearing failure....just the hub seal that was fooked this time..NOTE TO SELF DO NOT BUY ****PART BEARINGS AND SEALS AGAIN. :doh::doh::doh::doh::doh::doh::doh::doh:
 
Jus declared mine SORN as i aint had the time to replace the clutch master cylinder yet. It only went back in may! would like to get the roof off it and get it the garage and clean the chassis up and wax it. Its also due MOT at the end of the month
 
Went to the beach
Came home and stuck the Rangie on fleabay
Got to get it tested now eh ?
 

Attachments

  • Lamd Rover 003.jpg
    Lamd Rover 003.jpg
    21.5 KB · Views: 190
  • Lamd Rover 001.jpg
    Lamd Rover 001.jpg
    46.8 KB · Views: 161
  • Lamd Rover 014.jpg
    Lamd Rover 014.jpg
    23.7 KB · Views: 189
  • Lamd Rover 015.jpg
    Lamd Rover 015.jpg
    24.2 KB · Views: 171
Finally got round to tweaking Muckys' engine a lil' today, and finished off the winch install......noticed the timing belt is overdue for chaning accoring to the log book ....... noticed the o/s swivel seal is leaking ....... ho hum.

once all that's done .............I might even wash it a lil.
 
I have't done anything yet…but will be fitting these beauties later, which have just arrived..

Gear box, transfer box and timing belt cover breathers, with a neat manifold to join with my axle breathers and then run one single pipe up to the snorkel!!

6248_246910820612_727855612_8418351_6930750_n.jpg
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
375
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
412
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
681
Knappster
Knappster
I
Re-coding of ABS Module after repacement
Replies
10
Views
729
invisible999
I
C
Freelander 1 crank no start
Replies
1
Views
1K
niccage
N