Mark Piercy · Dec 18, 2019

Here is a trick for you, not a tell all but can be used as an indication.
When a window motor is jammed or shorted the interior lights will dim slightly when the button is pressed similar to a jammed or duff starter.

Dopey · Dec 18, 2019

Ok I will try that, I got another motor just in case (they are cheap enough second hand) but after changing the pack over and it wasn't that, thought I would cover all the things that might go wrong seeing I'm in there

Mark Piercy · Dec 18, 2019

Does the mirror respond to the pack and speakers? Hopefully it's the motor and not the outstation.
https://images.app.goo.gl/zgsxfHQJGaVvaFYi8

Dopey · Dec 18, 2019

Mirrors fine ( think) will check lol

Dopey · Dec 18, 2019

Nearside works, driver side not, but I don't think it worked before then the window went, someone sideswiped the mirror, and I didn't fix it 100% so it could be that (I just put a new glass on it) I have so many things to do, but when I go to do them I'm huffing and puffing trying to do them

Dopey · Dec 18, 2019

Sorry.... Honda Civic Type R 2009 front n/s/f brake is binding, anyone have a clue as to why that would happen??

Kev12 · Dec 18, 2019

Sticky slider pins most likely

Dopey · Dec 18, 2019

I put copper grease on it, think I should have put lithium on them??

Kev12 · Dec 18, 2019

Ideally you need to take the slider pins right out and give them a good clean up, there will be old hard grease stuck to them. Same goes for the hole they slide in. Should be silicone grease otherwise i would say lithium would be better than copper

Mark Piercy · Dec 18, 2019

Dopey said:
Sorry.... Honda Civic Type R 2009 front n/s/f brake is binding, anyone have a clue as to why that would happen??

Or a sticky piston, when was the brake fluid last changed?

Dopey · Dec 18, 2019

Mark Piercy said:
Or a sticky piston, when was the brake fluid last changed?

been a few years at least

Dopey · Dec 18, 2019

It starts binding after a few miles when the brakes warm up its fine for the first few miles its strange you would think it would be the other way around!!

Henry_b · Dec 18, 2019

Copper grease will cause the bellows around the slider to swell, it'll also cause the slider to drag..

Copaslip is an assembly compound not a lubricant.

Dopey · Dec 18, 2019

Red rubber grease is that the same thing?

Henry_b · Dec 18, 2019

Dopey said:
Red rubber grease is that the same thing?

No that is rubber specific.

Silicone paste is good on the sliders.

Marine grease is another..

Dopey · Dec 18, 2019

Thanks

Mark Piercy · Dec 18, 2019

Dopey said:
It starts binding after a few miles when the brakes warm up its fine for the first few miles its strange you would think it would be the other way around!!

Don't forget the disks heat up and swell.
Before driving it and cold, do a light push test with no handbrake, after a good run try it again. If it won't roll as easy then it could be a piston problem.
The sliders will be stiff hot or cold.
Then remove the problem wheel and it's same axle other side.
Try to return the piston or caliper into the fully retracted state on both calipers.
A stiff piston will require a lot more force to return it into filly retracted. Check for heat traces on the disk face also, I. E. Bluing.

Dopey · Dec 18, 2019

ok ta

Mark Piercy · Dec 18, 2019

Dopey said:
ok ta

Your welcome.

Henry_b · Dec 18, 2019

Throttle body heater decided to leak, i only bodged it 2 years ago

Painted it black too

So i bodged the bodge of my bodge

Well fumbled member....

Well-Known Member

Well fumbled member....

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well fumbled member....

Well-Known Member

Well-Known Member

Think outside, no box required.

Well-Known Member

Think outside, no box required.

Well-Known Member

Well fumbled member....

Well-Known Member

Well fumbled member....

Think outside, no box required.

Similar threads