Datatek said:
Wot no photos?
Click to expand...
IMG_20190504_160007.jpg
IMG_20190504_160018.jpg
IMG_20190504_163423.jpg
IMG_20190504_163450.jpg
IMG_20190504_160038.jpg
 
Grrrrrr said:
You'll definitely need the tool to hold the fuel pump and lock the flywheel. Then there's the adapter and dial guage to set the pump. And socket for the injector pipes as they have to come off. Think that's it. Have you got a beavertail or suitable trailer?
Click to expand...

No, no trailer. I have all the locking tools, dial gauge and stuff. Also have replacement o rings for the FIP. Why is it always that lower o ring you can't get to? :rolleyes:
 
Mukiwa said:
I have the locking tool, not sure about the gaskets you can do it without taking the head off from what I've seen. (Hopefully!)
Click to expand...

No, no need. Follow RAVE. Inlet manifold and high pressure pipes off. Locking tools in place and unbolt. Trickiest part is getting the pump lift right. Best do it a few times to make sure you have it consistently in the right place. Oh, and FFS don't turn the engine backwards.
 
Grrrrrr said:
No, no need. Follow RAVE. Inlet manifold and high pressure pipes off. Locking tools in place and unbolt. Trickiest part is getting the pump lift right. Best do it a few times to make sure you have it consistently in the right place. Oh, and FFS don't turn the engine backwards.
Click to expand...
I read about what happens when you turn the engine backwards... I don't fancy that
 
Mukiwa said:
not sure about the gaskets you can do it without taking the head off from what I've seen. (Hopefully!)
Click to expand...

INLET manifold gaskets x6

No need to take head off but you may need to take inlet off to get at pipes and FIP easier. If you have plastic manifold you may get away with it

Pre EGR alloy inlet gasket is - stc2203
With EGR plastic inlet is - stc4187

6 of whichever ;)
 
Looks like it’s had the plate rammed in there hard. All I’ve heard about solid flywheels on a P38 are negative opinions. How different do you find it??
 
RangeRoller dt said:
Looks like it’s had the plate rammed in there hard. All I’ve heard about solid flywheels on a P38 are negative opinions. How different do you find it??
Click to expand...
On the Transit, I need to change down a little earlier or there is some vibration at very low revs, otherwise it's fine:D
On Transit forums there is talk of crankshaft failures but I think that might come down to how people drive. some versions of the Defender with a similar engine have a solid flywheel as standard. I can't see the problem on the M51 as it's a six.
 
No problems with solid flywheel on my defenders, original lasted their entire lifetime. Dual mass is only to smooth it out I think, P38 is smooth enough I would have thought VCU or those rust asteroids on diff will sort any small vibration out
 
Clutch lever bushes replaced. Forgot replacement spiral pins so back to Land Rover for those tomorrow.
 
Fixed the drivers side air vent while stuck on the M61 waiting for them to re open it. Let’s see if I can find something else to fix. There must be something
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
2K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
549
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
719
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
807
Grrrrrr
Grrrrrr