Datatek
Well-Known Member
Ah, so you definitely want an HP24The engine I meant... Sorry
Thats that cleared up then
Datatek
Well-Known Member
No, I'm trying to pluck up the courage to fit it to mineAre you trying to sell this unit my matey??
I understand Keith. It is a big jobNo, I'm trying to pluck up the courage to fit it to mine
Datatek
Well-Known Member
Henry b's valve block bolt tightening has improved the flaring between 2 & 3 dramatically, wish I had known about it sooner, might have saved the clutch.I understand Keith. It is a big job
Does the box slip at all Keith?
Datatek
Well-Known Member
No, not at all, just the lazy shift 2 to 3 which I drive round by doing a slight lift when I know it's going to shift. It tows fine even with that other P38 on the hook. Lukas transmission fix helped a lot but gave hard shifts 3 to 4. Since the Henry b bolt tightening with one oil change and no transmission fix it's perfect when cold and much better when hot than it was. I plan to do a second oil change in spring.Does the box slip at all Keith?
I used a trannyfix. It made the box awful as if it was sticky... I rinced it all out. Right then, I'm going out for a run.
Catch up with you later, have a good day Keith
Catch up with you later, have a good day Keith
RangeRoller dt
Well-Sprung Member
So you don’t have wet feet and have to top the coolant up now and again?
Been for spin. On startup clutch has little pressure hard to get gears in. After a run it’s fine gotta be air in there somewhere
Been for spin. On startup clutch has little pressure hard to get gears in. After a run it’s fine
gotta be air in there somewhere
Datatek
Well-Known Member
Humidity in the fluid, needs fresh fluid. Had that exact problem on my MR2, new fluid and it's fineSo you don’t have wet feet and have to top the coolant up now and again?
Been for spin. On startup clutch has little pressure hard to get gears in. After a run it’s fine
RangeRoller dt
Well-Sprung Member
I flushed and bled the brakes so that’s new, could be the old fluid in the clutch part. Bleed it out is the answer I think, too cold today though
I seem to recall is you undo the bleed nipple on the slave you can just drink your tea and watch it flush itself.
Henry_b
Think outside, no box required.
Transfix ups the viscosity of the ATF which in turn ups the line pressure to help with worn clutches, however as it says on the can it won't fix a totally worn out box..I used a trannyfix. It made the box awful as if it was sticky... I rinced it all out. Right then, I'm going out for a run.
Catch up with you later, have a good day Keith
Nothing will it tends to play havoc with the solenoids.
If you want to help prolong the life try Dextron 6 which is the fully synthetic replacement for Dex II and III
I wish I hadn't touched that bloody valve section..... So the flare has gone but now slowing right down to a near stop and the box shunts and a clatter from the running gear..... So.. I've got strip the valve unit out and check that the retaining spring clips aren't catching on any of the three shuttles..... Fu ked off isn't near my sentiment right now
I have to wait until next Sunday as the ramp is packed this week......
I have to wait until next Sunday as the ramp is packed this week......
Henry_b
Think outside, no box required.
What did you do to it?I wish I hadn't touched that bloody valve section..... So the flare has gone but now slowing right down to a near stop and the box shunts and a clatter from the running gear..... So.. I've got strip the valve unit out and check that the retaining spring clips aren't catching on any of the three shuttles..... Fu ked off isn't near my sentiment right now
I have to wait until next Sunday as the ramp is packed this week......
Exactly?
Datatek
Well-Known Member
At least you have plenty of workI wish I hadn't touched that bloody valve section..... So the flare has gone but now slowing right down to a near stop and the box shunts and a clatter from the running gear..... So.. I've got strip the valve unit out and check that the retaining spring clips aren't catching on any of the three shuttles..... Fu ked off isn't near my sentiment right now
I have to wait until next Sunday as the ramp is packed this week......
Datatek
Well-Known Member
What ever it was it was not exactly right
RangeRoller dt
Well-Sprung Member
Doesn’t sound a bad thing budI have to wait until next Sunday as the ramp is packed this week......
