EAS never gets old my Nan has issue with getting into the old P38 so when I came in and parked up people were looking at the old girl and then I drop her to access a gent came across and asked how it did it ;) .. ;)
Very handy..

That's partly why I got mine so mother could get in and out, then she went into hosital and never came out so never got to try it.
My brother had a new hip fitted today so it will come in handy when I pick him up from hospital next week.:D
 
Brakes on one of my P38's seem quite sharp. the other one they are a bit wooden and need a harder push, I think it's down to the brake pad material.
If there is air in one of the front brake lines, it's likely to pull to one side when braking hard.
I didn't notice it pulling one way or the other, but I'm sure the pedal goes down further than it did
 
I didn't notice it pulling one way or the other, but I'm sure the pedal goes down further than it did
Possibly air in the modulator, equally it may just be that the new modulator has different characteristics, as I said my 2 are markedly different.
Have you tried a full on emergency stop?
Otherwise you could do the bleed routine again.
 
Possibly air in the modulator, equally it may just be that the new modulator has different characteristics, as I said my 2 are markedly different.
Have you tried a full on emergency stop?
Otherwise you could do the bleed routine again.
Didn't get the opportunity to do an emergency stop, but managed to get the tc and abs engaged, didn't have any issues
 
After the vehicle is running and just stopped, the fluid in the pipe system is still held under pressure from the pump and accumulator for a while. After some time the valve block might leak back some of the fluid back into the chamber, if a NR valve is not sealing fully, which makes the level rise. Not really an issue as the fluid gets drawn back into the system the next time it fires up and the level goes back down.="kermit_rr, post: 5263698, member: 150759"]Struggled a bit with the fluid level, thought it was on the money, put the lid on and few mins later it was over flowing :eek: seems ok now i think[/QUOTE]
 
Took the old bus to the old bus to the stables some people I know are trying to get the hang of horse riding..

So I took 'em in the RR.

xADg4Ii.jpg


EAS never gets old my Nan has issue with getting into the old P38 so when I came in and parked up people were looking at the old girl and then I drop her to access a gent came across and asked how it did it ;) .. ;)

Very handy..
Let the air out the tyres?
 
Drove to work, brakes still ok!! Engine getting 2-3c warmer than normal but not overheating.. viscous fan failing i wonder..
 
Drove to work, brakes still ok!! Engine getting 2-3c warmer than normal but not overheating.. viscous fan failing i wonder..
How do you know that the engine is getting "2-3c warmer? From memory, on the diesel, the gauge will stay around the 12 0clock position from about 85C to 100C
 
How do you know that the engine is getting "2-3c warmer? From memory, on the diesel, the gauge will stay around the 12 0clock position from about 85C to 100C
I always run with 'torque' Android app running.
Yes the idiot gauge always sits at 12 o'clock, but the app gives actual temp measured at the sensor.
Normally it's at 91-92 while driving, going up slightly going up a hill etc but today is running at 93 and quickly rising to 94-95 when i slow down
 
Replacing the modulator has resolved the bad noise, but not the pressure loss :( it gets up to pursue quick enough, but loses it within an hour or so
 
Found out my water pump is starting to fail so looks like I might be taking her off the road over the winter and spruce her up. Seems low on power so going to go for a top end rebuild I think
 

Similar threads