90truckcab · May 20, 2012

todays installment includes fitting the truck cab to tub seal

then the roof to cab seal

then dropping the cab in to position on the tub

then i lifted the roof in to position and fixed with a few loose bolts till its ready to be tightened

then fitted the door hinges loosely, ( wich scretches yet paint , so dont copy this )

then fitted the doors

turns out there is a slight difference in the bulkhead position , so i will be altering the position of the bulkhead to chassis brackets with the steering coloumn etc to gain myself 8 - 10mm any other difference can be taken out by the windscreen position, by altering the wing nuts

Sean · May 20, 2012

very nice, could we have a close up of the cab floor please

sorry, could I have a close up ......

johnny curt 1 · May 20, 2012

nowt else i can say exept its bloory beautifull that is

crashbox · May 20, 2012

Very nice. I suspect I may have fitting issues with my S3 rebuild later on but interesting to hear how you intend adjusting it to fit.

90truckcab · May 20, 2012

Sean said:
very nice, could we have a close up of the cab floor please

sorry, could I have a close up ......

yes mate, will take you a pic tomorrow , i presume you mean the ally floor pans etc?

johnny curt 1 said:
nowt else i can say exept its bloory beautifull that is

cheers mate , hows yours looking

crashbox said:
Very nice. I suspect I may have fitting issues with my S3 rebuild later on but interesting to hear how you intend adjusting it to fit.

will keep you up dated, but as usual , it wont go to plan , and il end up using a stihl saw and lump hammer to make final ajustments

Sean · May 20, 2012

90truckcab said:
yes mate, will take you a pic tomorrow , i presume you mean the ally floor pans etc?

I wuz teasing you about what looks like CP floor pans

90truckcab · May 21, 2012

Sean said:
I wuz teasing you about what looks like CP floor pans

i was gunna take you a close up ! ,

as someone donated that checker plate ,it seemed a shame not to use it , the paint dont last 5 mins on the floors so it seemed a good idea, brakes all that yellow up too,

johnny curt 1 · May 21, 2012

mines not lookin too bad at the moment ive replaced all me tranny and gearbox oil yesterday and to my horror it wasnt gear oil in them i dont exactly know what it was exept the nearest thing to it comes out of an engine after chronic HGF so its been a full flush and inspection with new gaskets throughout

thankfully no rust on the cogs or anything though

also got to help me old mate over the street to free him up to get me pump timing sorted
a favour for a favour

ieuandavies · May 21, 2012

woooowww!!

makes mine look tatty

will have to do mine again now!!

90truckcab · May 22, 2012

well , as described i adjusted the angle of the bulkhead as required to gain my 10mm,

nice and straight

a quick respray of the passenger door post as last week i gave it a quick wipe with wat i thort was a clean rag, turned out what ever was on it reacted with the paint and blistered it to ****

so i stripped it , primed and painted it again tonight

and its started......... ****in brake fluid, had to crack the top union to let it draw some fluid into the new cylinders as the split systems higher than the original , i knew i spilt a drop, but i thort the two buckets of water had done the trick , obviously not ....

sooooo, thats all comin out and gerrin resprayed again

90truckcab · May 22, 2012

i hope my towels come clean in the wash

90truckcab · May 22, 2012

just in from glazing my cab, weathers been spot on so sprayed my new door tops today too, looking more and more like a landrover now , pics tomorrow

johnny curt 1 · May 22, 2012

90truckcab said:
just in from glazing my cab, weathers been spot on so sprayed my new door tops today too, looking more and more like a landrover now , pics tomorrow

awwww cant we have just 1 piccie to look at till tomorow

Harri Edwards · May 23, 2012

comeing along well now mate cmoon more pics....... hhaha

90truckcab · May 25, 2012

johnny curt 1 said:
awwww cant we have just 1 piccie to look at till tomorow

Ok Johnny, a few pics

cleaned me glass for door tops

had number plates made

spent a few hrs setting timing up

mounted a few things on bulkhead

90truckcab · May 25, 2012

fitted copper vacum pipe to dizzy and carb

90truckcab · May 25, 2012

finished riviting round doors

door tops on

glazed cab

Harri Edwards · May 27, 2012

looks well

samc88 · May 27, 2012

Very nice. Can't wait to get started on mine now but I've got to wait until our garage is built.

90truckcab · May 28, 2012

At long last its been on its maiden voyage, soon to find the carb not quite right, air screw not making any difference to pick up, main jets have been "cleaned" out by a previous owner so it over fuells and chokes its self when pulling off from lights, have ordered new webber so hope that solves the problems, off to sand blasters in morning to pick up tail gate and few last bits, so more pics to come

Well-Known Member

Banned

Well-Known Member

Well-Known Member

Well-Known Member

Banned

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Drivels spiritual representative

Well-Known Member

Similar threads