cowasaki
Well-Known Member
What was it?
What was it?
cowasaki
Well-Known Member
Galvernisednuts
Active Member
I used the alarm led on the speedo with mine too
Fitting the clocks did me a massive favour, the square end of the speedo drive gear was broken so I replaced it with a blue 20 tooth one
My speedo had been a bit out as it still had a disco gear in it (disco transfer box fitted)
Fitting the clocks did me a massive favour, the square end of the speedo drive gear was broken so I replaced it with a blue 20 tooth one
My speedo had been a bit out as it still had a disco gear in it (disco transfer box fitted)
Galvernisednuts
Active Member
Cos I fitted a Tdci bulkhead I gained the 10as alarm module and central locking stuff so there was a pink wire to connect to the one for the td5 speedo led
Just wired it up and yep it works
Just wired it up and yep it works
HowiePage
New Member
My TD5 binnacle was all working fine till I had take it back out to get speedo out to have mileage changed to correct mileage, when plug the warning binnacle back in, the glow plug light and battery light no longer work everything else works fine. I've check they are fully pushed in in the plug which they are, is there any obvious thing mean only these lights don't work?
Also my temperature gauge will randomly now go to fully hot then drop back down to normal position and flutter about, could this be the sender or a bad earth?
Also my temperature gauge will randomly now go to fully hot then drop back down to normal position and flutter about, could this be the sender or a bad earth?
could be, but if your bat light is broke, your alt mightn't be working until you fix it.
how did you sort it?
temp gauge with heater on is another earth fault. you checked the earth bolt/on the engine bulkhead to the right of the brake servo?
HowiePage
New Member
I took it all apart and started again, I obviously didn't have a wire pushed in properly somewhere. Once it was back together it worked fine. so cables tied it up and taped it to keep it tidy and stop it moving around.
If it an earth fault I will check, I wasn't sure what it would be. No I haven't! That be job for weekend! Thanks for all your help.
If it an earth fault I will check, I wasn't sure what it would be. No I haven't! That be job for weekend! Thanks for all your help.
Last edited:
IamRobbie
Well-Known Member
Glad I've stumbled upon this thread as I plan on putting a td5 bulkhead on my 200tdi 90, I wasn't going to use the binnacle from the td5 but I will now be trying this mod
.. Is it possible to use the whole td5 dash including door sensors and the steering wheel and rack as it's all there for me??
Maybe by adapting my 200tdi loom onto the td5 lights and appliances.
.. Is it possible to use the whole td5 dash including door sensors and the steering wheel and rack as it's all there for me??
Maybe by adapting my 200tdi loom onto the td5 lights and appliances.
cowasaki
Well-Known Member
The TD5 dash should go on without issue and the main differences with the wiring will be to the binnacle. "door sensors" ? How many splines on 200TDi and TD5 steering wheel? You'll need a speed transducer but can you get the one from the TD5 that's being taken apart?
IamRobbie
Well-Known Member
Door sensors I was talking about were the little push in things that turn the lights on when the door opens and it.Doesn't matter how many splines are on the steering wheel, I have the whole thing still together. What I was wondering was do I use the complete dash, with the td switches, indicators clocks hazard button ect ect and can all that connect up to my 200 tdi loom...
I know the modification to make the td5 speedo and dash lights work already so if I used my 200 tdi dash I could use the td5 clocks but I want to know if I can use the whole td5 dash. Headlight switch ect
I know the modification to make the td5 speedo and dash lights work already so if I used my 200 tdi dash I could use the td5 clocks but I want to know if I can use the whole td5 dash. Headlight switch ect
