kanekelly94 · Jul 5, 2019

Help!
My Land rover is struggling to start.
I'm certain Fuel is the issue
I think it could be the fuel pump.
The Car won't start and then when I turn the ignition on and press the pedal 5 times the pump will then initiate and I can hear it and then it will start.
Do you rekon it is a new pump job or could this be something else?
Maybe Air in the system or needs a flush out?
I've left the engine management light flashing going through the cycle for 2mins and it will start after.
But then when stop it and try start it again it won't have it.

Once started I can then drive it around with absolutely no problems
No power loss etc

kanekelly94 · Jul 5, 2019

Land rover discovery 2 td5

kanekelly94 · Jul 5, 2019

I think maybe the pump is noiser than what it normally is.

To literally start the car I have to wait for the pump to finish making noise then it starts else it just turns over

jamesmartin · Jul 5, 2019

injector washers and pump are the 2 things id look at and change air bleed valve as a matter of course

swatts70 · Jul 5, 2019

Injector seals. Mine was exactly the same. Came on out of nowhere and got worse and worse over next few weeks. Changed seals and been perfect since.
Use only genuine LR seals.

kanekelly94 · Jul 6, 2019

Thanks guys
I'll check the oil see if it's increased

Is there anything to look out for when changing these?

Bobdog · Jul 6, 2019

kanekelly94 said:
Thanks guys
I'll check the oil see if it's increased

Is there anything to look out for when changing these?

Have you changed the fuel filter recently?

kanekelly94 · Jul 6, 2019

Bobdog said:
Have you changed the fuel filter recently?

Nope
6000 miles ago I did

sierrafery · Jul 6, 2019

kanekelly94 said:
Thanks guys
I'll check the oil see if it's increased

Is there anything to look out for when changing these?

The oil level is not affected by the copper washers which are the problem in your case, diesel in oil is caused by the rubber o-rings but these have nothing to do with starting issues, see this http://www.discovery2.co.uk/Injector Seals.html

biggles_butler · Jul 6, 2019

I had the same problem - nosy pump - difficult to start. Injector washers knackered - oil doesn't increase (as above).
Use genuine washers otherwise you'll be doing it again in 12 months.
Other place air can get in is the filter housing.

kanekelly94 · Jul 6, 2019

biggles_butler said:
I had the same problem - nosy pump - difficult to start. Injector washers knackered - oil doesn't increase (as above).
Use genuine washers otherwise you'll be doing it again in 12 months.
Other place air can get in is the filter housing.

I've bought genuine seals and coppers today maybe make a start on it tomorrow
Change the injector harness and gasket aswell.
Been sat on my side for months.

Did you use the correct £99 tool to remove them?
Was going to attempt the 6mm Allen key or half a water pump plier

kanekelly94 · Jul 6, 2019

sierrafery said:
The oil level is not affected by the copper washers which are the problem in your case, diesel in oil is caused by the rubber o-rings but these have nothing to do with starting issues, see this http://www.discovery2.co.uk/Injector Seals.html

Thanks! Really useful guide that!

sierrafery · Jul 6, 2019

kanekelly94 said:
Did you use the correct £99 tool to remove them?

IMO that slide hammer is not a good ideea cos those shocks might not be ''healthy" for the solenoids... half pipe plier or allen key are perfect for the job

kanekelly94

Member

kanekelly94

Member

kanekelly94

Member

jamesmartin

Well-Known Member

swatts70

Active Member

kanekelly94

Member

Bobdog

Well-Known Member

kanekelly94

Member

sierrafery

Well-Known Member

biggles_butler

Member

kanekelly94

Member

kanekelly94

Member

sierrafery

Well-Known Member

Similar threads