Walshie1987

Walshie1987

Active Member
Hi,

Every time I post it seems to be about a problem so sorry. I also keep saying I'm scrapping the RR and yet here we are 5 years on :)

So the latest bit of fun is that I went to take the kids to school this morning and heard a horrible grinding noise from the drivers read wheel, like metal on metal. Only when moving and seems to be worse when going forward, then reversing back.

I initially thought brake pads, but on inspections looks like there's plenty left on them, so I started shaking the disc shield round the disc, then I saw a screw drop down. Using a bit of force I managed to get the screw out of the cover, I tried moving the car again and the noise was still there.

I'd like help identifying the screw first off, that might give me a bit of a clue, here is it, it looks like a 5mm Hex socket:

20230601_120209.jpg



And here's a video of the car moving and the sound:



As I said I keep threatening to scrap it but it's got 10months MOT and I annoyingly still love driving it, so see what's up with it this time :D

Thanks in advance!
 
Thanks! The handbrake doesn't work really at all - could explain a few things! A garage replaced the handbrake shoes for me last year - I don't think they had a clue what they were doing to be honest.

I just googled it and it is the Handbrake shoe hold down!! 👏 What a start!! Now to figure out how to get it back on properly, any ideas? I will research too.

Thanks again!
 
Remove the wheel.
remove the caliper.
Back off the adjuster.
remove a screw.
take off the disc.

Replace and then reverse procedure:).

You will probably best get a new set, first as there should be a spring and a washer (thing) chances are they are mangled.

Simple ;).

J
 
Brilliant, thanks! Yeah will get them ordered now, might as well put new handbrake shoes on them too whilst I'm at it.

Thanks Marjon, that was really hepful 👍

Here's a video I found too explaining in detail if it helps anyone else out:

 
Note they say in the manual to renew the caliper bolts too.

Think its a CYA on land rovers part, up to you.

J
 

Attachments

  • Rear disc.pdf
    642.3 KB · Views: 206
Also you need to follow the bedding in procedure if fitting new.
When I looked at mine they appeared to have plenty of meat left. as at the end of the day they are only applied when vehicle is stationary. If they were new last year don't see they would need it.

Did the handbrake work good after they did the work? wondering if they didn't do a "bedding "procedure.

J
 
marjon said:
Note they say in the manual to renew the caliper bolts too.

Think its a CYA on land rovers part, up to you.

J
Click to expand...
Nice 1, if I'm going to do it I might as well do it right.

Now going totally again that, I can't get the parts until early next week and I should be going away this weekend. Would I be stupid to put the screw back in for the weekend and go away (40 miles drive)?
 
Walshie1987 said:
Nice 1, if I'm going to do it I might as well do it right.

Now going totally again that, I can't get the parts until early next week and I should be going away this weekend. Would I be stupid to put the screw back in for the weekend and go away (40 miles drive)?
Click to expand...

You need disc off to do it as the spring and clipcan only fitted that way.

theres a chance the bits are recoverable when you take the disc off. but any good motofactor would probably have them to match.

J
 
marjon said:
Also you need to follow the bedding in procedure if fitting new.
When I looked at mine they appeared to have plenty of meat left. as at the end of the day they are only applied when vehicle is stationary. If they were new last year don't see they would need it.

Did the handbrake work good after they did the work? wondering if they didn't do a "bedding "procedure.

J
Click to expand...
No it never worked properly, worked enough to barely get it through the MOT but they told me it was the cable that had stretched and that was the issue and wanted a stupid amount to fit a new one. They weren't RR speciailists - I only use specialits now, but they can't fit me in for at least a week - pretty comfortable in doing this myself to be honest. Shouldn't be too much work.

I definitely don't think they did a bedding in procedure!
 
marjon said:
You need disc off to do it as the spring and clipcan only fitted that way.

theres a chance the bits are recoverable when you take the disc off. but any good motofactor would probably have them to match.

J
Click to expand...
Brilliant, I'll get the disc off tonight and see what I can do, not going to risk safety for the sake of a few days.
 
the slot in the back plate may have rotted out, if so get a bolt and 2 washers fit a washer over the end of the bolt pass through the spring shoe and back plate put other washer over bolt use a nylonnut and do up just enough to apply tension on spring, will work till you get a new back plate
 
badfluffy said:
the slot in the back plate may have rotted out, if so get a bolt and 2 washers fit a washer over the end of the bolt pass through the spring shoe and back plate put other washer over bolt use a nylonnut and do up just enough to apply tension on spring, will work till you get a new back plate
Click to expand...
Just to close this off! This was 100% what it was! That's exactly the solition I used too! Thanks badfuffy! Saved me alot of effort.

RR will sadly be gone in Oct (probably scrapped) Love it, but far too many issues popping up recently, almost weekly. This fix will keep me going until then

Cheers,
Chris
 
You must log in or register to reply here.

Similar threads

B
Rear bumper choices
Replies
7
Views
574
BigJessie
B
Montyjohn
P38A Any tips for getting the EAS pump piston off its spline?
Replies
18
Views
1K
gstuart
gstuart
A
L322 L322 M62 Cabin heating issues
Replies
5
Views
270
biketeacherdave
biketeacherdave
ar1g3
P38A P38 rattle at idle
2
Replies
26
Views
3K
roythebus
R
V
Screw size. Voltage stabilizer
Replies
7
Views
795
Phil Maddox
P