Maxlondon
Active Member
Ok thanks, I will check with the others, it's raining now can't fit it yet...???
Other thing while waiting i blew the head with a compressor to get the metal left by the skimming and stuck a brass wire brush on a drill to clean up the outside . Nothing wrong with that isn't it ?
MaxyMan
Well-Known Member
Should be fine it's only ally so just don't go at it too heavy handed with scrapers and screwdrivers like I've seen before, just nice and gentle or use abit of brake cleaner or something similar but the outside of the head doesn't really matter too much. Make sure to blast the head off with an air line after you've cleaned it make sure all the pushrod channels and waterway etc havnt got any crud brushed in.
i know it doesn't matter but I would like to clean that engine well and since it's out , best time to do it !
Maxlondon
Active Member
Yep that's what it was, thanks.
Putting the camshaft back in place with the pushrods not in order... I realised 1 was way too high while the one next to it looked very low , can I just readjust them to 0.2mm and that'll be fine ? As right now I've got a valve almost all the way down !
Maxlondon
Active Member
Just finished puting everything back on in between 2 rains, didn't change anything... it's not leaking water anymore though , but it is still smoking like crazy and sound like it's working on 2 cylinders.
Same as before ... when I slacken the fuel pipe of the cylinder 3 and 4 it doesn't change anything and 1 and 2 make it almost stall...
I am giving up...
Any ideas ?
Piston rings..? Valve seals ?
I can't believe I paid someone to make sure that's what it was and it is not..
Same as before ... when I slacken the fuel pipe of the cylinder 3 and 4 it doesn't change anything and 1 and 2 make it almost stall...
I am giving up...
Any ideas ?
Piston rings..? Valve seals ?
I can't believe I paid someone to make sure that's what it was and it is not..
jamesmartin
Well-Known Member
could be 2 poor injectors 3 and 4,poorly set tappets (have all the adjusters got about the same amount of thread above the nut )was head skimmed ,do you have pics of gasket ,head ,block when it was in bits prior to cleaning
Flossie
Well-Known Member
If you haven't got any valves not completely closing, ie- no clearance between valves and rockers then it's time for the compression test.
It's smoking because the fuel isn't burning in 3 and 4.
Did you determine if it was water or fuel dripping from the exhaust joints?
If it is fuel I suspect, if you run it long enough, it'll appear again.
It's smoking because the fuel isn't burning in 3 and 4.
Did you determine if it was water or fuel dripping from the exhaust joints?
If it is fuel I suspect, if you run it long enough, it'll appear again.
jamesmartin
Well-Known Member
ok ,you can prove it by swapping the positions if nothing else appears
Maxlondon
Active Member
I got the injectors tested before doing the gasket, the guy said they are all good, I got the head pressure tested and skimmed yes,
setting the adjusters, 2 push roda where about 10mm too high , had to crank the engine for them to set in place ( tried everything before ) then reopened the rocker cover and readjusted them all to 0.2mm seems all fine now. I don't have any pics no but I still have the old gasket (which look pretty new actually )
jamesmartin
Well-Known Member
how did you set tappets rule of 9 ,are threads above lock nut about the same on all
Maxlondon
Active Member
The mechanic said it was definitely water. I got some o ring to try to fix my compression tester, I will try tomorrow as I am exhausted and it started raining again
Maxlondon
Active Member
no I set them just 1 by 1 starting from the front ones, it looks like there's a tiny leak from the exhaust manifold right in front of cylinder 4 as well, like microscopic bubbles, tried to tighten it more but still does it
yes the threads on the adjuster screws looks roughly the same
Maxlondon
Active Member
I didn't put them back in order and it is always the same cylinders that doesn't change the pitch when I slacken the fuel pipe
jamesmartin
Well-Known Member
you have to set by the rule of 9 by turning engine over till one valve is just fully open the counting from the front and taking that from 9 which is which you adjust , 3 fully down adjust 6 2 fully down adjust 7 etc
Maxlondon
Active Member
so i need to turn the engine on and off 8 times ? could that simply this making it smoking so much ? because I rechecked the gap (0.2mm) after turning it on and off and it was still good
jamesmartin
Well-Known Member
you turn it over by hand to set tappets, the proper gap for each valve can only be determined when its opposing number from 9 is just fully open,poorly set tappets would cause a lot of issues
