Datatek
Well-Known Member
Disconnecting the battery can scramble the BECM
FOB buttons can easily and cheaply replaced, plenty on Ebay, the lock mechanism is not very strong for continual key use.
FOB buttons can easily and cheaply replaced, plenty on Ebay, the lock mechanism is not very strong for continual key use.
RangeRoller dt
Well-Sprung Member
Blue dot is early unit but they are all same crap. Don’t be tempted to buy a later version (unless Marty’s) people put different colour stickers on them - all useless.
I’ve unplugged my RF and fixed my fob, even though it all works now I still use the key in lock out of habit. Mine is 95 and although many have trouble with the locks I’ve used mine for years no issues yet. Always handy sort it now so you have an option2 if it does go
I’ve unplugged my RF and fixed my fob, even though it all works now I still use the key in lock out of habit. Mine is 95 and although many have trouble with the locks I’ve used mine for years no issues yet. Always handy sort it now so you have an option2 if it does go
Datatek
Well-Known Member
You do not need to enable EKA to use the FOB, I run both mine with the EKA and Immobiliser disabled, saves a lot of hassle and I use the FOB all the time
how do you disable EKA? i could only see to disable the immobiliser, which I've done already and made life so much simpler as the antenna is unplugged from the receiver
Datatek
Well-Known Member
I don't have a Nanocom so I cannot tell you precisely but on Faultmate there is a box for EKA on the same page as the immobiliser, from that box you can turn EKA off and on.
Does that not put you in a vulnerable situation if the BECM should throw a wobbly and go into alarm state?
Or if the alarm and EKA are turned off will it stop that happening?
J
Datatek
Well-Known Member
If the BECM goes into an alarmed state you are in deep doo doo and need FAultmate with the 035 module to disarm it, the EKA and Immobiliser are nothing to do with that and it's something that rarely happens.
With EKA turned off, you never need the EKA code if the FOB goes out of sync, just open the door with the key and off you go, a simple unlock/lock cycle with the key resyncs the FOB.
With the immobiliser turned off, you will never get the Engine Immobilised press FOB message. If there is a loss of sync between the BECM and the EDC, diagnostics will be needed as is the case with the Immobiliser and/or EKA turned on. This ONLY applies to the diesel, the V8 is different and I have no idea if any of this would apply.
just found it.
there is option to enable/disable immobiliser, alarm, key warning and EKA
Datatek
Well-Known Member
Do not turn off the alarm or key warning.
thanks for the heads-up. i've not changed anything since disabling the immobiliser a while ago
whats the reason behind not turning the alarm or key warning off? my klaxon doesnt work anyways
Datatek
Well-Known Member
Alarm is for insurance purposes and is not likely to cause you any problem as the Klaxon is disconnected, key warning is the same, it does no harm and I have not investigated any side effects that might occur if you turn it off.
Thanks, I understand the need for (the very expensive module) from BBS, to unlock the BECM.
But thank you for the explanation, and yes the V8 is different from what I can see. Just trying to up to speed and confirm how they are different, and why.
I have never had any problems with the OF and wonder if a lot has been turned off and the fact it runs a different ECU means I never will? ( probably just done it now
).J
Datatek
Well-Known Member
The enabling code in the diesel EDC is a fixed number, the BECM simply has to have the matching number to send to the EDC. On the V8 the engine ECU uses a rolling code. I do not know what other differences there may be.Thanks, I understand the need for (the very expensive module) from BBS, to unlock the BECM.
But thank you for the explanation, and yes the V8 is different from what I can see. Just trying to up to speed and confirm how they are different, and why.
I have never had any problems with the OF and wonder if a lot has been turned off and the fact it runs a different ECU means I never will? ( probably just done it now
J
Thanks, that’s the way I was understanding it.
But as the OF uses an OMEX (Haven’t actually found it yet to confirm) which seems to be able to talk to the gearbox ecu, I am assuming it doesn’t require the code (as if the standard ecu had been made “standalone”)
I (so far) have had nothing more than needing to set windows and radio, long may that continue
J
Thanks, I understand the need for (the very expensive module) from BBS, to unlock the BECM.
But thank you for the explanation, and yes the V8 is different from what I can see. Just trying to up to speed and confirm how they are different, and why.
I have never had any problems with the OF and wonder if a lot has been turned off and the fact it runs a different ECU means I never will? ( probably just done it now
J
That would make sense. The GEMS was much more integrated with the BECM. The diesel was a cut and shut job and I think the Thor was similar so the OF would be even more so.
martyuk
Well-Known Member
To clarify a few things from my research and testing:
EKA enabled/disabled - disables the need for the EKA - say it's gone flat with the battery connected, then you'd need the EKA more than likely when the power is restored. Turning EKA should stop this from being required. The only time it will screw you is if the EKA is turned OFF and KEYCODE LOCKOUT comes up on the dash - it implies the vehicle is in an alarm lockout stage, and needs the EKA - which if it's off, it won't accept.
If you have a V36 or later BECM, the 'Disarm' section in the Nanocom will still allow you to put your EKA number in and disarm from the lockout (in most cases - sometimes even then the BECM will not do it, and will need sending away to someone like myself to have the lockouts reset using the faultmate/BECM CPU module.
That being said - I've had a few test BECMs on the bench and I've never been able to get one with the EKA disabled into a state where I can't recover it with the key - I've tried multiple different scenarios, including simulating breaking into the vehicle whilst it's alarmed, and with the EKA off, it was simple to reset every time.
Immobiliser enabled/disabled - this disables the passive part of the immobiliser system. The bit where it will re-immobilise the vehicle are 30 odd seconds, with the idea being that when the vehicle detects a key being put back in the ignition it pulses the coil around the key barrel, which then induces a small current in a coil in the key fob, which triggers it to send an unlock code - which then re-mobilises the vehicle and will allow starting. If this is ON and your key fob stops working, then you will need the EKA every time it automatically immobilises again to be able to cancel it and start the vehicle, which is one of the reasons most people turn it off - it creates a headache in my opinion, especially if your fob is iffy, or you've only got one. Turning the passive immobiliser OFF disabled this automatic immobiilising, but the vehicle WILL still immobilise when it is locked and alarmed with the key in the door.it also turns OFF the coil around the ignition (the BECM doesn't pulse it when it detects the key in the ignition), which also then disabled the 'friendly sync' where an out of sync fob will automatically resync when you put it in the ignition. The only way of syncing the fob, with passive immobilisation disabled is to do it with the key in the door.
Alarm enabled/disabled - pretty self explanatory - with it disabled it won't trigger any of the alarm responses if it detects the vehicle has been broken into. I've not seen any other detrimental effects having it switched off on the test units I've played with, but would leave it switched on out of habit myself. I believe that the security LED on the dash which usually flashes when the alarm is armed, will still flash as a deterrent (at least on a number of the boards I've tested - might be software/firmware related) when the vehicle is locked, but the alarm isn't ACTUALLY armed.
Key Warning... I believe this is just a gonging sound from the instrument pack sounder which gets pretty annoying pretty fast, and sounds if the vehicle detects the key is in the ignition, and the drivers door is open. Removing the key from the ignition shuts it up. Most vehicles I've looked at have it disabled by default, and I think it was more NAS spec that had it enabled.
Immobilisation strategy. Regarding the link between the BECM and the engine ECU and Diesel/Petrol differences.... Early EDC vehicles appeared to just ground the immobiliser line between the BECM and engine ECU and that was the immobiliser trigger, nothing complex at all. Though these were swapped out pretty early on for the 'Late EDC' version (it's not a 99MY change as you'd expect to line up with the GEMS/Thor changeover on the petrol vehicles - it was actually in '96/'97 from memory). Late EDC has an immobiliser code which is hard coded in the engine ECU, and this code then is programmed into the BECM. The BECM then transmits this code to the engine ECU constantly, in pulses every 144ms? Quite rapidly anyway. When the BECM is disarms/non immobilised and the key is turned to position 2, it transmits the code constantly until the ignition is switched back off (or to Pos I)
GEMS petrol has a code in the BECM which it transmits to the engine ECU. If the 2 become out of sync, then instead of programming a code back into the BECM, you tell the GEMS ECU to enter security learning mode and it will then take the next code sent to it by the BECM as it's immobiliser code, and stores it - so instead of changing it at the BECM end, it's done at the engine ECU end. When you turn the key to POS II, BECM transmits the code to the engine ecu where it checks it, and then if it's valid, then engine ECU illuminates the Check Engine Light as a response that it's happy. When the BECM sees this trigger, it stops sending the immobiliser code altogether, and then will allow the starter motor to operate. The Thor petrol is pretty much the same as the Late EDC - code is hard written into the engine ECU, and then programmed into the BECM to match. It's then constantly transmitted when the ignition is on.
Both the EDC and Thor Petrol models DON'T respond back to the BECM to say that they are happy with the code. GEMS won't crank until the CEL has been switched on (confirmation of valid code from engine ECU), and thus WON'T crank or show CEL if out of sync. The EDC and Thor petrol will always still crank - as the BECM has no idea if the code is valid or not, as no feedback from the ECU. So it's programmed to always allow the starter to run, and then the actual starting is decided by the engine ECU - if code is valid, then injectors/spark etc are allowed. If code isn't valid, then these are disabled. On a Diesel, I believe it will shut off the fuel stop solenoid or something in the FIP to prevent fuelling if the code doesn't match.
Hope that explains a bit more in detail how the various systems/options work for those who are interested.
Marty
EKA enabled/disabled - disables the need for the EKA - say it's gone flat with the battery connected, then you'd need the EKA more than likely when the power is restored. Turning EKA should stop this from being required. The only time it will screw you is if the EKA is turned OFF and KEYCODE LOCKOUT comes up on the dash - it implies the vehicle is in an alarm lockout stage, and needs the EKA - which if it's off, it won't accept.
If you have a V36 or later BECM, the 'Disarm' section in the Nanocom will still allow you to put your EKA number in and disarm from the lockout (in most cases - sometimes even then the BECM will not do it, and will need sending away to someone like myself to have the lockouts reset using the faultmate/BECM CPU module.
That being said - I've had a few test BECMs on the bench and I've never been able to get one with the EKA disabled into a state where I can't recover it with the key - I've tried multiple different scenarios, including simulating breaking into the vehicle whilst it's alarmed, and with the EKA off, it was simple to reset every time.
Immobiliser enabled/disabled - this disables the passive part of the immobiliser system. The bit where it will re-immobilise the vehicle are 30 odd seconds, with the idea being that when the vehicle detects a key being put back in the ignition it pulses the coil around the key barrel, which then induces a small current in a coil in the key fob, which triggers it to send an unlock code - which then re-mobilises the vehicle and will allow starting. If this is ON and your key fob stops working, then you will need the EKA every time it automatically immobilises again to be able to cancel it and start the vehicle, which is one of the reasons most people turn it off - it creates a headache in my opinion, especially if your fob is iffy, or you've only got one. Turning the passive immobiliser OFF disabled this automatic immobiilising, but the vehicle WILL still immobilise when it is locked and alarmed with the key in the door.it also turns OFF the coil around the ignition (the BECM doesn't pulse it when it detects the key in the ignition), which also then disabled the 'friendly sync' where an out of sync fob will automatically resync when you put it in the ignition. The only way of syncing the fob, with passive immobilisation disabled is to do it with the key in the door.
Alarm enabled/disabled - pretty self explanatory - with it disabled it won't trigger any of the alarm responses if it detects the vehicle has been broken into. I've not seen any other detrimental effects having it switched off on the test units I've played with, but would leave it switched on out of habit myself. I believe that the security LED on the dash which usually flashes when the alarm is armed, will still flash as a deterrent (at least on a number of the boards I've tested - might be software/firmware related) when the vehicle is locked, but the alarm isn't ACTUALLY armed.
Key Warning... I believe this is just a gonging sound from the instrument pack sounder which gets pretty annoying pretty fast, and sounds if the vehicle detects the key is in the ignition, and the drivers door is open. Removing the key from the ignition shuts it up. Most vehicles I've looked at have it disabled by default, and I think it was more NAS spec that had it enabled.
Immobilisation strategy. Regarding the link between the BECM and the engine ECU and Diesel/Petrol differences.... Early EDC vehicles appeared to just ground the immobiliser line between the BECM and engine ECU and that was the immobiliser trigger, nothing complex at all. Though these were swapped out pretty early on for the 'Late EDC' version (it's not a 99MY change as you'd expect to line up with the GEMS/Thor changeover on the petrol vehicles - it was actually in '96/'97 from memory). Late EDC has an immobiliser code which is hard coded in the engine ECU, and this code then is programmed into the BECM. The BECM then transmits this code to the engine ECU constantly, in pulses every 144ms? Quite rapidly anyway. When the BECM is disarms/non immobilised and the key is turned to position 2, it transmits the code constantly until the ignition is switched back off (or to Pos I)
GEMS petrol has a code in the BECM which it transmits to the engine ECU. If the 2 become out of sync, then instead of programming a code back into the BECM, you tell the GEMS ECU to enter security learning mode and it will then take the next code sent to it by the BECM as it's immobiliser code, and stores it - so instead of changing it at the BECM end, it's done at the engine ECU end. When you turn the key to POS II, BECM transmits the code to the engine ecu where it checks it, and then if it's valid, then engine ECU illuminates the Check Engine Light as a response that it's happy. When the BECM sees this trigger, it stops sending the immobiliser code altogether, and then will allow the starter motor to operate. The Thor petrol is pretty much the same as the Late EDC - code is hard written into the engine ECU, and then programmed into the BECM to match. It's then constantly transmitted when the ignition is on.
Both the EDC and Thor Petrol models DON'T respond back to the BECM to say that they are happy with the code. GEMS won't crank until the CEL has been switched on (confirmation of valid code from engine ECU), and thus WON'T crank or show CEL if out of sync. The EDC and Thor petrol will always still crank - as the BECM has no idea if the code is valid or not, as no feedback from the ECU. So it's programmed to always allow the starter to run, and then the actual starting is decided by the engine ECU - if code is valid, then injectors/spark etc are allowed. If code isn't valid, then these are disabled. On a Diesel, I believe it will shut off the fuel stop solenoid or something in the FIP to prevent fuelling if the code doesn't match.
Hope that explains a bit more in detail how the various systems/options work for those who are interested.
Marty
Datatek
Well-Known Member
One small point Marty, the BECM does not pulse the passive coil round the ignition lock, it simply applies a voltage to the oscillator built into the oil assembly.
