Hippo
Lord Hippo
Only fred worth reading in ere.
Hippo
Lord Hippo
He was a man of the people. So the people followed him. Having sold them a pot of gold at the end of the rainbow, we find its a minus pot of gold. Having left the eu agricultural policy, telling farmers they will be betterer oft, we left and the uk gov gives them less in replacement subsidues. Farming was one of the industries wiv a higher % voting for what he said would be betterer. How dumb were they. Dumb enuff to let him stand wiv them during the recent farming protests. The man who made them poorerer is protecting them. To be more precise, goal hanging the latest opertunity to be in the headlines. Farmers will confirm he rode into town onner unicorn.And now we have another retard over the pond tariffs, blaming disabled peps , as bad as the red bus with lies written on it, but you can only blame the voters, GB news done interviews and thay couldn't find a single pep that would vote leave now
Hippo
Lord Hippo
Typical leaver. Dumb enuff to fink yer can leave twice.Well they weren't looking hard enough. I'd vote leave again tomorrow.
Maybe they've gone to a different supplier ?
Hippo
Lord Hippo
Eye did wonder that. Also the one eye fort were pregnant. Not so sure now. It could be wiv its young iffit is. It may just be they have had their time and naychair has taken em.
Have you done a 'Hard Reset' - AKA - turned it off, then turn it on again or Battery off wait half and hour, (for tea and bikkies), shove it back in again ?
Corrected that for you ------
saxavordian
Well-Known Member
Hard reset ?
Hammer
Drop of two feet
Swift boot in the air from a size nine steel toe cap
Standing in front angrily shouting profanity enough to embarrass a devil
Pouring hot tea on the keyboard
Allow nextdoor neighbour's bull mastiff to mate with it.
Or perhaps press the on off button
Do what I did, by a separate keyboard (they are cheap and plug into an USB socket) and turn the original one off on your lappy. It works fine.
But mine had a bit more wrong with it, it went well wonky!!!!!!
According to W, who knows far more than I do about this stuff, leaving the lappy running on the battery, and letting the battery go flat is acksherly a better hard reset than taking the batt out.
She did try to explain why to me but I fell asleep halfway through!
(Can't beeleeve I'm on here giving IT advice!!)
She did try to explain why to me but I fell asleep halfway through!
(Can't beeleeve I'm on here giving IT advice!!)
Hippo
Lord Hippo
When electronics powers up there's a slight delay in getting steam pressure up to supply all components wiv power. There be a problem if yer processor wakes up faster than yer ram memory. The processor may want to start using said ram whennit ain't ready. Circuits wiv many different steam pressures fer different components make it more complex. Not unusual to have plus and minus 3.3, 5, 10, 12 and 15vdc in more demanding circuits. Some have lower pressures of plus and minus 1.5 or 1.8vdc. Fings are made worse if the power supply is slow to wake up. The different voltages will be regulated seperate. Some will be up to pressure before others.
So how does they solve this? Components like ram memory, processors, flash memory, ard drives etc have a reset line. That signal can be high or low. When the reset is active, components sit ready waiting in reset for the reset line to switch to active. When it does they start wuking.
Yer typical processor circuit has a 'delay on' circuit. It does worrit says ont tin. Its a small circuit wiv a timer, used to create a delay to start the circuit wukking after steam pressure has built up. Typically 20 or 50 milly seconds. The ootput from the delay on circuit is connected to the reset line. The job of the delay on circuit is to hold the reset singal in reset, fer a small number of milly seconds, to allow steam pressure to build up in the rest of the circuit. Once complete, it changes the state of the reset line from high to low (or low to high depending on the logic) which triggers fings to start wuking. The processor will then start loading program code into its registers. Yer phooter is now starting to wuk.
Wots the difference between first powering a processor circuit up and resetting it? Nowt. When a processor circuit resets it triggers the delay on circuit to control the reset line. Fings like ram can quickly wipe themselfs during a reset. The processor will ferget where it is in the program and start from the beginning again when said reset line is released after the requested delay on, completes. After the delay on milly seconds delay timer completes its time delay, the reset line switches and fings start oft fresh again. In reality it dun't matter if ram is cleared. The processor uses a new page in its notepad each time its powered up to remember which memory address locations it uses to store fings to remember.
So resetting a phooter ain't no different to pulling the power oot, letting steam pressure drop, then applying power again. The only benefit to removing power is when fings like power supplies mess up. Current limit potection could kick in iffit can't regulate itself if one of the steam power volt rails hassits steam sucked oot quicker than normal due to high current demand when fings sometimes go wrong. Like during component failure.
So how does they solve this? Components like ram memory, processors, flash memory, ard drives etc have a reset line. That signal can be high or low. When the reset is active, components sit ready waiting in reset for the reset line to switch to active. When it does they start wuking.
Yer typical processor circuit has a 'delay on' circuit. It does worrit says ont tin. Its a small circuit wiv a timer, used to create a delay to start the circuit wukking after steam pressure has built up. Typically 20 or 50 milly seconds. The ootput from the delay on circuit is connected to the reset line. The job of the delay on circuit is to hold the reset singal in reset, fer a small number of milly seconds, to allow steam pressure to build up in the rest of the circuit. Once complete, it changes the state of the reset line from high to low (or low to high depending on the logic) which triggers fings to start wuking. The processor will then start loading program code into its registers. Yer phooter is now starting to wuk.
Wots the difference between first powering a processor circuit up and resetting it? Nowt. When a processor circuit resets it triggers the delay on circuit to control the reset line. Fings like ram can quickly wipe themselfs during a reset. The processor will ferget where it is in the program and start from the beginning again when said reset line is released after the requested delay on, completes. After the delay on milly seconds delay timer completes its time delay, the reset line switches and fings start oft fresh again. In reality it dun't matter if ram is cleared. The processor uses a new page in its notepad each time its powered up to remember which memory address locations it uses to store fings to remember.
So resetting a phooter ain't no different to pulling the power oot, letting steam pressure drop, then applying power again. The only benefit to removing power is when fings like power supplies mess up. Current limit potection could kick in iffit can't regulate itself if one of the steam power volt rails hassits steam sucked oot quicker than normal due to high current demand when fings sometimes go wrong. Like during component failure.
Me Dad like them fish blocks but with that Golden Mash stuff of carrot, swede and tatoe plus whatever else is lurking at the bottom of the veggie bag ...
Well I've learned something today. Pooters work on steam. And I always thought they worked on smoke like other leccy kit. Every day's a skool day.
Stone56
Well-Known Member
Yep we be doing a full circle, FL traction engine coming soon powered by logsWell I've learned something today. Pooters work on steam. And I always thought they worked on smoke like other leccy kit. Every day's a skool day.
