jai_landrover said:
I'm sure when I got a set of cheapos last year they were in a plain box with mintex stamped in back of the metal part of the pad. Looking good Jamie keep up the hard work!
Did you ever get to the bottom of the bearing problems??

Jai
Click to expand...

the discs where in a plain box put the pads where mintex boxes, i had a small vice, 4ft breaker bar, 4 and 8lb hammers and a crowbar and it still took 3hrs, i didnt put thread lock on either but they where bloody tight i used the imact driver which goes up to 300nm, as for the bearings i think it was just me done somethings wrong:eek:, took apart and cleaned an greased again then put back together and been fine since, i did notce the angle of the two front wheels are different, driver side top tips towards body slightly and the other is paralel with the spring.

i need to look at something else aswel, when i took the half shafts out the back all that came out was rust colour water, shouldnt this have been oil?

jamie
 
Last edited:
jamiehoward said:
the discs where in a plain box put the pads where mintex boxes, i had a small vice, 4ft breaker bar, 4 and 8lb hammers and a crowbar and it still took 3hrs, i didnt put thread lock on either but they where bloody tight i used the imact driver which goes up to 300nm, as for the bearings i think it was just me done somethings wrong:eek:, took apart and cleaned an greased again then put back together and been fine since, i did notce the angle of the two front wheels are different, driver side top tips towards body slightly and the other is paralel with the spring.

i need to look at something else aswel, when i took the half shafts out the back all that came out was rust colour water, shouldnt this have been oil?

jamie
Click to expand...

i had a horrible brown merky oil, it was very ming, its where ur diffs get hot, then u dunk em in water n mud n its just sucks it in. drain it, leave it to drain fully and replace the oil,

hour job to do both if you leave it to drain completely

Dan
 
99claydond said:
i had a horrible brown merky oil, it was very ming, its where ur diffs get hot, then u dunk em in water n mud n its just sucks it in. drain it, leave it to drain fully and replace the oil,

hour job to do both if you leave it to drain completely

Dan
Click to expand...

thanks, i have been wadeing two or three times recently, i went through redbourn ford after the rain on the weekend and it was deep enough for my headlights to fill with water and upset the missus coz she thought she was gona get wet feet :D

p.s wot is bst oil to use
 
jamiehoward said:
thanks, i have been wadeing two or three times recently, i went through redbourn ford after the rain on the weekend and it was deep enough for my headlights to fill with water and upset the missus coz she thought she was gona get wet feet :D

p.s wot is bst oil to use
Click to expand...

I nearly went through it Sunday afternoon with no snorkel...so glad I didn't, it looked pretty deep :rolleyes:
 
jamiehoward said:
i did notce the angle of the two front wheels are different, driver side top tips towards body slightly and the other is paralel with the spring.
Click to expand...

Not a great idea to check the wheels using the springs (or body-work!!) as a datum as they're easily moved a bit. Might be worth taking to a kwik-fit type place and have them measured up properly.

I have a procedure for doing this at home, but can't find it .. typical ... ;)
 
Paul D said:
Not a great idea to check the wheels using the springs (or body-work!!) as a datum as they're easily moved a bit. Might be worth taking to a kwik-fit type place and have them measured up properly.

I have a procedure for doing this at home, but can't find it .. typical ... ;)
Click to expand...
i can notice it from all angles now iv had a proper look, can see it is without lineing it up with anything, is this something im gona strugle to do myself.
 
well glad it went together ok, i really would do them to the specific torque figure and locktight the bolts as they have the whole weight of the vehicle when braking and thats alot of force applied however you look at it
You wouldn't wanna over tighten them over stressing the bolts or not get them all torqued up equallly. As for wheel alignment if its that noticable then somthing is wrong possibly bodywork outterline or somthing more worrying defo worth looking at more closely.
Jai
 
jai_landrover said:
well glad it went together ok, i really would do them to the specific torque figure and locktight the bolts as they have the whole weight of the vehicle when braking and thats alot of force applied however you look at it
You wouldn't wanna over tighten them over stressing the bolts or not get them all torqued up equallly. As for wheel alignment if its that noticable then somthing is wrong possibly bodywork outterline or somthing more worrying defo worth looking at more closely.
Jai
Click to expand...

i will double check them in a week or as i dont have much driveing to do and i gota get some wheel bearings and do them y im there, got phone bill to pay 1st:(, on the bright side my last insurance payment this month and i get 3 months free so that free's £220 a month to play with :D
 
Been trying to think what it could be, unlikely to be a bent axle, but that's not unknown, and as it's the front wheels it's a possibility that one of the swivels or swivel bearings has a problem. Certainly it shouldn't be 'different' to the other so it's something that I'd get checked sooner rather than later.
 
jai_landrover said:
new beast? This mean even wider tyres? Or p.s where did you fit your air compressor on your 90? Jai
Click to expand...


hello mate, tyres are the same at the moment as the ones i want arnt in the country yet. As for compressor if your talking about locking diffs i havent done these yet, possibly going with KAM lockers so will be elec not air. Me motor will be on one of the stands at billing so you will get to see her there if not b4 :D:D
 
well the landy needs a run out but will be out at a comp Sunday near north weald airfield so thats the shakedown before derbyshire. Jai
 
Glenn321 said:
hello mate, tyres are the same at the moment as the ones i want arnt in the country yet. As for compressor if your talking about locking diffs i havent done these yet, possibly going with KAM lockers so will be elec not air. Me motor will be on one of the stands at billing so you will get to see her there if not b4 :D:D
Click to expand...


What stand are you gunna be on mate, i will be there and so will my motor :)
 
Mr Ryder i spotted you today in luton you flashed what i thought was me to go round the bus but it was a guy coming out :) bout 4ish emm just down from biscotmill
 
You must log in or register to reply here.

Similar threads

A
Peak District lanes
Replies
8
Views
2K
Anaconda
A
A
Non Scratchy Greenlane Trip Berkshire/Wiltshire
Replies
10
Views
2K
Anaconda
A
T
Any Series Owners in the Phoenix Area?
Replies
9
Views
612
Bobsticle
Bobsticle
A
Greenlane trip 19th August
Replies
7
Views
2K
Anaconda
A
Shogun243
LLandrillo - Wayfarer
Replies
1
Views
926
300bhp/ton
300bhp/ton