plumbfisher

plumbfisher

Active Member
Evenin' all,
I thought that the time was right to tackle the O rings replacement. It's been leaking a bit more since using the heater recently. Followed all the useful guides (esp. thanks to Stufer) and got into it. Even cut the duct to get max access. But the screwhead is knackered and I've tried every philips screwdriver I've got, plus bits in sockets and anything else that I thought might shift it. What with the messing about its dripping even more now and I can't move it either way, loosen or tighten, and the cross in the head is becoming rounded off. I've given up for tonight, but any advice on what I could try tomorrow would be appreciated. I'm not sure I can even get a drill in to drill it out ... :(
 
Some have had success using a cutting paste or valve paste to enhance grip and to try and prevent the bit slipping in the head....worth a shot!
 
As you've given up for the night the last job you should be doing is spraying some release penetrate stuff goo on it before you go in for tea.
 
First of all soak in penitrating fluid leave to soak .
Then with just an 3:8 extention bar spend at least 15 minutes tapping the head the tapping action can break any antifreeze that has gumned up the threads . Try to tighten as well as loosen you can find that doing up has a slightly better grip than trying to undo it other wise its dash out as you can't possibly get any grip on the screw head otherwise!
 
Ah well, thanks for your help. I suppose it was too much to hope for a magic fix... I'll have another go at it in the morning, perhaps the penetrating oil will have freed it up a bit. I'll try tapping it some more, then put some valve paste in the screw head and try again. Thanks again - I'm off for a drink or two and try not to think about having to take the dash out...
 
plumbfisher said:
Ah well, thanks for your help. I suppose it was too much to hope for a magic fix... I'll have another go at it in the morning, perhaps the penetrating oil will have freed it up a bit. I'll try tapping it some more, then put some valve paste in the screw head and try again. Thanks again - I'm off for a drink or two and try not to think about having to take the dash out...
Click to expand...

If so its not so bad just bloody time consuming go get ****ed ;)
 
had exactly the same problem so I took the dash out for better access, I used this guide. Not too bad but I took it slow to avoid breaking anything. I wouldn't be surprised if someone had previously used Loctite on mine.

O Rings Part 2
 
plumbfisher said:
Ah well, thanks for your help. I suppose it was too much to hope for a magic fix... I'll have another go at it in the morning, perhaps the penetrating oil will have freed it up a bit. I'll try tapping it some more, then put some valve paste in the screw head and try again. Thanks again - I'm off for a drink or two and try not to think about having to take the dash out...
Click to expand...
You can try holding a preheated large Phillips screwdriver on the screw, hopefully the heat transfer may help :)
 
I had to drill the head off the screw but be very careful if you use this method as one slip or to much heat transfer to the plastic will cut or melt it and then you really up the creak slow and steady with several breaks will get the job done got it all done in 7hrs and thats dash out and dash back in when you put it all back together you are best to get a allen head bolt/screw
 
You must log in or register to reply here.

Similar threads

A
P38A Heater matrix o-ring / pipes - advice needed !
2
Replies
23
Views
2K
romanrob
R
ar1g3
P38A Radiator drain plug o-ring troubles
Replies
7
Views
2K
ar1g3
ar1g3
MikeFl4
P38A Brake bleeding disaster
Replies
16
Views
2K
MikeFl4
MikeFl4
tankduck
Td5 fuel hoses......leaks and o rings!
Replies
2
Views
1K
Brown
Brown
Graculus
L405 Engine oil leak / fumes in cabin
Replies
10
Views
2K
marjon
marjon