Pringy

Member
Hi all
First ever post has I've only owned a freelander for a few month's I've just taken the air inlet manifold off and given it a good clean out and taken the the egr valve off and blanket it off I've put everything back on car minus one bolt off the bottom left hand side of the manifold everything has all titened down and car seems to be running fine just wondering if it will be ok long term
Thanks
P.S great site got some real good tips off herep
 
Thanks for your reply pal ive got a boat load of nuts and bolts but struggling to find one that fits do you know if they are a special type or not mate
 
Think they’re M7 bolts which is unusual - can buy from Land Rover or BMW dealer
Many thanks to you both most appreciated I'll sort it out over the weekend the old girl is in for mot thismornig fingers crossed
 
Last edited:
Sorry to be a pain and really appreciate your help so far its been a great help but do you know what the torque settings are for the air inlet manifold
Thanks
 
As above nip up then a 1/4 turn and tighten them up by jump each one starting from the end, I just finished changing one over for a R40 member, then the heavens have opened up.

iGNza5nl.jpg
 
OOH - you nip tight!
With an M6 thread I wouldn't take it past 10Nm unless you have hardened bolts (10.9 or 12.9).
Thanks for your advice pal I've stripped a few threads in my time got me in an hole lot of bother ive borrowed a torque wrench from work think I'll get myself one so I've always got one to hand
 
Lol
They're 7mm bolt/studs. I got the torque figures from the first set I removed a manifold, which hadn't been removed since it was built. I don't actually use a torque wrench for most fixings, except wheels and torque essential bolts and nuts. After many years, you can tell when the fixing is tight enough.
 
Thanks for your advice pal I've stripped a few threads in my time got me in an hole lot of bother ive borrowed a torque wrench from work think I'll get myself one so I've always got one to hand
I agree with Nodge and I rarely use a torque wrench for smaller fasteners (M8 and smaller) unless it is something critical like a cylinder head bolt. After you have snapped a few steel bolts inside an aluminium casting you develop a feel for what is about right - also known as paranoia.

If you are getting yourself a torque wrench it is a good idea to think about where you are going to be using it. For this sort of fastener I would be using one with a 1/4" drive and a maximum torque of about 50 Nm. The larger ones are too unwieldy and not very accurate at low torque settings when you are working on piddlin little screws. On the other hand if you are worried about the torque on your hub nut you need something a bit more macho. On the other, other hand, the little ones tend to be more expensive.

There are plenty of tables around on the internet showing the standard tightening torques for all sorts of threads - like this one http://www.norbar.com/Portals/0/downloads/TorqueValueGuide.pdf.
 
I agree with Nodge and I rarely use a torque wrench for smaller fasteners (M8 and smaller) unless it is something critical like a cylinder head bolt. After you have snapped a few steel bolts inside an aluminium casting you develop a feel for what is about right - also known as paranoia.

If you are getting yourself a torque wrench it is a good idea to think about where you are going to be using it. For this sort of fastener I would be using one with a 1/4" drive and a maximum torque of about 50 Nm. The larger ones are too unwieldy and not very accurate at low torque settings when you are working on piddlin little screws. On the other hand if you are worried about the torque on your hub nut you need something a bit more macho. On the other, other hand, the little ones tend to be more expensive.

There are plenty of tables around on the internet showing the standard tightening torques for all sorts of threads - like this one http://www.norbar.com/Portals/0/downloads/TorqueValueGuide.pdf.
Nodge68 and Blodge thank you very much for your advice most appreciated
It's a cracking motor to be onist it had been in the same family since brand new the history with the car is amazing the only little problem with the car is the valve stem seals it puffs out a bit of blue smoke on first start up but soon clears i can live with that
 
the only little problem with the car is the valve stem seals it puffs out a bit of blue smoke on first start up but soon clears i can live with that

Has the breather filter been changed every couple of years, with the PCV valve being changed at the same time?
 
Yes it's been changed every service and just to make sure i changed it myself last week pal but not sure about pcv valve ive never heard of it where would that be please
 

Similar threads