Your disco looks brilliant fella, that really is something to be proud of !

Have you re-sprayed it or is the colour as u bought it ??

Cheers dude, can't wait until its all done.

The colour is original. The paint code is posted earlier in the thread somewhere if that helps.
 
looks the mutz nutz mate.now stop messing and lets get it down waterlane :eek:
you have done a wicked job mate and you should be well chuffed with yourself.

Thanks Mark, yeah I'm happy with it so far. Been checking today and I need the master cylinder replacing :( but won't take too long and then we can go and play - I promise :D
 
Redhand:

Well stuck woods sounds about right tbh, there was some serious trouble to be bad there. The other guys found a lane that they didn't even attempt, I didn't see it cos my lardy disco couldn't get up the hill, but I can quite imagine that guy getting stuck for 4 days. The mud was the greasiest clay I have seen. Only thing similar is the clay bog at the far corner of the parkwood site, nobody gets through there.

1spin:

The mess was collateral :D
 
LOOKS FANTASTIC! i lifted my boot lineing the day. the center plate its perfect but everything round it is brown dust. dont fancy doin mine? :D a can see the next few days being spent wellding the tits out of the thing!!
 
LOOKS FANTASTIC! i lifted my boot lineing the day. the center plate its perfect but everything round it is brown dust. dont fancy doin mine? :D a can see the next few days being spent wellding the tits out of the thing!!

And then some... :rolleyes:

Welcome to rustyzone :)
 
rustyzone a lyk that lol. theres not even any point putin a seat belt on in the thing coz the mounting points are f**ked. a think a need ti learn ti weld! lol
 
LOOKS FANTASTIC! i lifted my boot lineing the day. the center plate its perfect but everything round it is brown dust. dont fancy doin mine? :D a can see the next few days being spent wellding the tits out of the thing!!

Easiest way is spot drill the welds and then chequer plate. Cheaper and looks better plus you can always unscrew it to get to the tank. Learnt this from Mr Noisy.

Yeah rusty zone is about right.:D
 
Ok this is my attempt to upload some descent photos of the Green Hornet. I hope it works.



d2b01676.jpg


4aa14c89.jpg

Wonderful "toy" is obtained. :)
Good luck with your work.
Happy New Year to all, good health and good luck.

..... Fleet, this is close to Basingstoke, If we are lucky and come in summer, can drink a beer.:rolleyes:
 
Just have the brakes to sort and I am done. will try another bleed this weekend and see if that works while i wait for the Master cyclinder dosh. a bit tight after christmas tbh. Kids..........

I am quite excited to get her on the road as i am tired of the bike at the moment. it needs new pivot bearings and a service too...........

btw, where did you get the tube for your tree sliders from?
 
Last edited:
Congratulations, your new toy looks the absolute dogs dangley bits. I've enjoyed your posts covering the build, can't wait to see some of the 'hornet in action,
 
Just have the brakes to sort and I am done. will try another bleed this weekend and see if that works while i wait for the Master cyclinder dosh. a bit tight after christmas tbh. Kids..........

I am quite excited to get her on the road as i am tired of the bike at the moment. it needs new pivot bearings and a service too...........

btw, where did you get the tube for your tree sliders from?


Its cds tube and I got it off a mate also got him to put a 90deg bends on them as well, want me to find out how much?
 
Congratulations, your new toy looks the absolute dogs dangley bits. I've enjoyed your posts covering the build, can't wait to see some of the 'hornet in action,

Cheers Waldershelf,

Don't panic there is still plenty to come and I plan on getting around a bit.
 

Similar threads