Check your 'injection value current' with Nanocom . I had a similar issue & the value was fluctuating from 0 to 3 , IIRC.
After adjustment it was okay. For the adjustment you need a hammer;)
Wammers or N2O will comment on specifics.
 
penska said:
Hello guys just to let you know still working away replaced wiring loom today an still the problem exists next I guess is fuel pump and then I honestly don't know
Click to expand...

As Sherlock Holmes said: "Pass the whiskey, Watson. And you don't get me some more opiates soon I'm going to cut your balls off." Something like that anyway.
 
penska said:
Is it possible for the immobaliser to kick in and cut the car out while its driving ?
Click to expand...
Should not do with key in ignition. Get someone with a Nanocom to disable immobiliser if you think it is that. Or better still get someone with a Nanocom to read the faults, if it keeps cutting out there has to be fault codes. Does it cut when driving or only when you are slowing down to make a slow turn or for lights Etc?
 
Doesn't matter it just cuts out when ever it wants steady spread slowing stopped even just turn engine off to get diesel it might not wanna start again
 
penska said:
Doesn't matter it just cuts out when ever it wants steady spread slowing stopped even just turn engine off to get diesel it might not wanna start again
Click to expand...

Would be thinking quantity servo then. Proper diag should tell you.
 
wammers said:
Should not do with key in ignition. Get someone with a Nanocom to disable immobiliser if you think it is that. Or better still get someone with a Nanocom to read the faults, if it keeps cutting out there has to be fault codes. Does it cut when driving or only when you are slowing down to make a slow turn or for lights Etc?
Click to expand...

penska said:
Doesn't matter it just cuts out when ever it wants steady spread slowing stopped even just turn engine off to get diesel it might not wanna start again
Click to expand...

May be demons:( in the ignition switch/relay.
 
I doubt it's ignition switch to BECM or anything like that. If the ignition switched power was dropping out, then there would be a lot more not working than just the engine cutting out.

HEVAC, Blower motors etc for a start would all shut off - which there's no mention of that happening - just the engine cutting out.
 
Well guys almost got a whole new car here lol replaced all the relays key fob repaired and now a new in tank fuel pump and .....drum role............still no joy
 
I think you need diag. Is there no-one near you with a Nanocom? Checked LZIR map?

If Wammers thinks quantity servo then you'd better check it and for that you need diag.
 
Your gonna need confirmation before you go digging in that hole buddy...
If your going to keep this bus and at the rate your savings are going into it I would think about nano diagnostics.
That'll be your best investment to date and then you can stop searching and start looking.;)




In the right places. Live data is a god send when you learn to read it:cool:
 
Could that green temp sensor be cutting it out at all as I might chuck that at it it it's possible it could be playing around
 
penska said:
Could that green temp sensor be cutting it out at all as I might chuck that at it it it's possible it could be playing around
Click to expand...
Without being too rude..... After 93 posts, are you at any point going to listen to the advice given and get some diagnostics on it?
 
After a hawkeye a snapon and a faultmate diagnostic hasn't picked up **** I don't think I will be thanks for your input
 
penska said:
After a hawkeye a snapon and a faultmate diagnostic hasn't picked up **** I don't think I will be thanks for your input
Click to expand...
Ah I see. I have obviously missed it or you haven't mentioned that previously. Otherwise I am sure those who have suggested you use diagnostics, right up to post #92, would not have felt the need to. Nor would I have asked if you were going to try them.
Sometimes , it helps to tell the full story.

Edit: meant to say after #1 where you say 'diagnostic machines" I have obviously missed ......


Double addit : My bad , you did mention it somewhere 3 pages ago. I obviously missed it. Which makes me curious as to why people are still saying for you to use diagnostics. Although maybe the nanocom can read more than the others you mention.
 
Last edited:
Which Faultmate?

Hawkeye is very limited on live data, and I doubt Snap On talks correctly the the Bosch system.
 
It's not all about finding a code!!
Live data from a dedicated diagnostic will reveal what is happening at any one point, it can used to record the engines behaviour while your driving also. By reading the graphs and info you can determine where to start;)
 
You must log in or register to reply here.

Similar threads

F
P38 DSE loss of power when driving
2
Replies
33
Views
2K
Mark Piercy
Mark Piercy
M
Classic Range Rover Suffix D Starting Issues - Advice required please
Replies
6
Views
721
Datatek
Datatek
R
2000 Thor 4.6 fuel/starting problems
Replies
5
Views
486
richardtamps
R
feyniriel
P38 alarm and immobilizer problems
2 3
Replies
42
Views
2K
Datatek
Datatek
V
P38 2.5 weird modification...
Replies
3
Views
711
Datatek
Datatek