Very damp NSR axle and back plate. P38a

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jimllshiftit

jimllshiftit

Active Member
Posts
227
Location
Warwickshire
Evening everyone. Hope your surviving the heat.

This week, im about to get stuck into the axles on the P38a, 1997 2.5 DT.

The front axle needs one CV joint and boot, so im doing both. Ill be in there anyway so ill change the ball joints as well and all this began because it was time to do the discs and pads, so ill do them too.

The rear axle will get new discs pads and calipers, but having just taken the rear wheels off I noticed that the OSR disc back plate is very damp with oil, inside and out. Its been "sweating" for about a decade but never enough to fail an MOT. It looks like it has deteriorated now so I might as well sort it while i've got it stripped. Could someone tell me whats likely to be causing that oil sweating?
 
Mine was exactly the same. As Brian said, seal on the half shaft. They're cheap and it's an easy job to do.
 
Brilliant. Thanks both of you. I was concerned it was the hub but the seal sounds like a lucky escape.

Any special tools required or can I just knock the seal in until its home?
 
No special tools needed i did mine when i changed the diff and just tapped them in square to the same depth as the old one, if you dont want to take the abs sensor out i just unpluged the connector and removed the caliper and disc and undone the hub and the whole assembly bearing hub shaft the lot pulls out
 
You do need a specific Loctite for the splines on the shaft. Can't remember which one but it's in Rave.
 
AHHHH!!!! I think the heat has melted my RAVE CD. I cant get into it to see the manual. It was fine last night.

Just searched Google for a free download but every link I click is dead. Could someone point me in the direction of a working link to a free download? Unless anyone would be kind enough to email one to me :)
 
jimllshiftit said:
AHHHH!!!! I think the heat has melted my RAVE CD. I cant get into it to see the manual. It was fine last night.

Just searched Google for a free download but every link I click is dead. Could someone point me in the direction of a working link to a free download? Unless anyone would be kind enough to email one to me :)
Click to expand...
That's why is always a good idea to copy RAVE from the CD to your hard drive.
I can't email you a link, but if you get desperate I can post you a CD with RAVE on it:)
 
jimllshiftit said:
AHHHH!!!! I think the heat has melted my RAVE CD. I cant get into it to see the manual. It was fine last night.

Just searched Google for a free download but every link I click is dead. Could someone point me in the direction of a working link to a free download? Unless anyone would be kind enough to email one to me :)
Click to expand...
The Dropbox link I put in the tech archive should still work. It's still in my dropbox.

https://www.dropbox.com/sh/o9m2uyenqtjmcm3/AAAzvtCBbo9nPJUtqD9lOk6ta?dl=0
 
Last edited:
Datatek said:
That's why is always a good idea to copy RAVE from the CD to your hard drive.
I can't email you a link, but if you get desperate I can post you a CD with RAVE on it:)
Click to expand...

Thats a very kind offer DT. It would be churlish not to accept. :) Do you want anything for it? Or is there an Auberge I can say thank you in, next time i'm heading to Ruffec.
 
jimllshiftit said:
Nice one, thanks. I wonder if there's something wrong with my computer though. I cant seem to open any of that either...
Click to expand...
Compatibility issue if you're using a newish version of Windows 10 or 11. Someone posted the settings to fix it but I can't for the life of me remember who.
 
Tenebreaux said:
Compatibility issue if you're using a newish version of Windows 10 or 11. Someone posted the settings to fix it but I can't for the life of me remember who.
Click to expand...

Looks like ill be buying you a drink next time im in "the Cross'" .... hadn't noticed where you were, earlier.

Im using windows 10 version 20H2... im wondering if Adobe is the issue.
 
jimllshiftit said:
Looks like ill be buying you a drink next time im in "the Cross'" .... hadn't noticed where you were, earlier.

Im using windows 10 version 20H2... im wondering if Adobe is the issue.
Click to expand...
RAVE runs on Win 10 in compatibility mode, you may have to try different options, Win 98 works for me. You may also have to scroll through several error warnings before it starts.
If you are going to Ruffec, you could always call in, I'm almost on your way:)
If you want the CD posted, PM me with an address.
 
Id be glad to DT. Used to drive up and down the N10 every few months but my work doesn't take me down to Cadiz as often as it used to. Have friends in Sauize Vaussais though so im still a frequent-ish visitor to your very charming neck of the woods.

PM to follow.
 
You must log in or register to reply here.

Similar threads

S
Freelander seized brakes and transmission fluid
Replies
10
Views
1K
Shabe
S
Hammer'n'tongs
Tyres wearing unevenly:- Axle ends out of alignment
Replies
9
Views
1K
Hammer'n'tongs
Hammer'n'tongs
MikeFl4
P38A Brake bleeding disaster
Replies
16
Views
2K
MikeFl4
MikeFl4
dconnrt
80's 110 - Braking pulling to the right in wet conditions
Replies
5
Views
545
dconnrt
dconnrt
DefendingLancashire
300TDI Four-parter: brake wear, lift pump / fuel filter, turbo, and bushes / squeaking
Replies
13
Views
472
miktdish
miktdish
Back
Top