Swivel rebuild problems

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Resurgam

Resurgam

Well-Known Member
Posts
190
Location
Ynys Môn
I've just spent a frustrating evening reassembling a swivel. First I forgot to put the seal on before bolting the swivel to the axle, then got the seal plate the wrong way around so had to take it off a second time, then destroyed the swivel to axle gasket by misaligning the holes.

Finally I got it all fitted but there seems to be a problem. The swivel will only turn slightly - certainly not enough to impact the lock stop, and I can only turn the drive shaft when it's completely straight on. I assume I've done something daft but I can't think what it is at the moment. Any help would be appreciated!
 
It does pay to have a diagram to hand or phone pic of what you are taking apart if you are not used to these things.
Can you turn the swivel with out the shaft in ? If so it may be you are not locating the shaft fully in place.
 
87_swivel_pin_housingfrom_(v)_la930456.png


1994 - 2006 from LA930456

pcLsQa8wRrO7PNo1iakIopkZGHIJSg9LLlFUDjcINgvEFlHmHLnnq-xS_yV_WBLYXU9hEefG93evbnN1uXdut6DVAK6OZDdkFJOOcUAeBN6gQ_ygguDN_nlXDPpkrLs
 
Thanks everyone. It's a 1993 200Tdi if that's relevant.

I'll check the position of the CV joint. I'd tested out the right combination of shims before I fitted the bits to the axle, but I'd also fitted the stub axle in advance which might have been a mistake. I'll have to take it all off and try again.
 
Resurgam said:
Thanks everyone. It's a 1993 200Tdi if that's relevant.

I'll check the position of the CV joint. I'd tested out the right combination of shims before I fitted the bits to the axle, but I'd also fitted the stub axle in advance which might have been a mistake. I'll have to take it all off and try again.
Click to expand...

Give it a go using a bolt in the hole at the end of the CV - if it is that, you should be able to pull it out (have the wheels straight forward).
 
Resurgam said:
Thanks everyone. It's a 1993 200Tdi if that's relevant.

I'll check the position of the CV joint. I'd tested out the right combination of shims before I fitted the bits to the axle, but I'd also fitted the stub axle in advance which might have been a mistake. I'll have to take it all off and try again.
Click to expand...
Take it to bits again and follow the exploded diagram above.... The only thing you should be able to get wrong is the shims for the swivel preload.
 
I'm fairly sure it's together in the right order. I didn't dismantle the CV joint when I took it all apart. The complete shaft has just been sat to one side so there shouldn't be anything wrong with it. I'll have a look next time I'm self isolating in the garage.
 
Resurgam said:
I'm fairly sure it's together in the right order. I didn't dismantle the CV joint when I took it all apart. The complete shaft has just been sat to one side so there shouldn't be anything wrong with it. I'll have a look next time I'm self isolating in the garage.
Click to expand...
it has to be seated fully into stub axle hand held like that whilst stub axle is bolted up, the shims on the end arent really vital as once fitted correct cv will stay in its favoured position
 
You must log in or register to reply here.

Similar threads

Rusty Bucket
Bottom swivel pin bolt torque
Replies
2
Views
444
tottot
tottot
dag019
Refresh my memory - swivel rebuild
Replies
4
Views
810
dag019
dag019
L
GETTING SWIVEL TO AXLE BOLTS OUT!! - they are out!!!
2
Replies
29
Views
2K
Forrest Gump
F
tottot
Brake hose mystery
Replies
13
Views
415
tottot
tottot
D
What IS this noise ?
Replies
12
Views
1K
dogdog1
D
Back
Top