Series 3 Snail heater blower

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
codfather79

codfather79

Well-Known Member
Posts
676
Location
Kent
Evening all.
Just taking apart the heater blower (guessing the motor is dead ☹️) ready for a clean up and found this inside

17231443712615587803759581589686.jpg


1723144439355294047724062045380.jpg


Any idea what it is and what it does?

Thank you 👍
 
Hopefully reassembly commencing today.
Just a thought, how does one test the resistor without a volt meter?
J rig a bulb and see if one wire makes it shine brighter than the other?
TIA👍
 
Wildefalcon said:
Run the fan straight from a 12v supply. Then use the resistor. Should be half speed...
Click to expand...
Thank you.
I'm trying to test the resistor before I reassemble the casing.
I've still got to buy a new motor as the old one is kaput 😕
Well, I've tried it on a 12v supply and it doesn't move!
 
codfather79 said:
Evening all.
Just taking apart the heater blower (guessing the motor is dead ☹️) ready for a clean up and found this inside

View attachment 323444

View attachment 323445

Any idea what it is and what it does?

Thank you 👍
Click to expand...

It's a 10 OHm, wire wound, ceramic resistor.
It halves the power getting to the blower motor so it runs slower.
It's in the airflow so it keeps cool.

I fitted two 10 OHm, 100W metal cased wirewound resistors in parrallel to mine and slow speed is now slightly faster than original and still slower than fast.

www.ebay.co.uk

2pcs 10 ohm 10 100W Watt Aluminum Housed Metal Case Wirewound Resistors | eBay

Resistance Value 10 ohm. Mounting Hole Dia 0.02cm/0.007". Plate Size 6 x 2.1 x 0.02cm/2.36" x 0.83" x 0.007" (L W H). External Material Aluminum. Color Gold Tone. Thread Size 0.02cm/0.007".
www.ebay.co.uk
 
I seem to remember taking my fan motor apart to give it a clean and fettle, you could probably revive it and it will certainly be better than a new one.
 
So, I've taken the motor apart.
I don't suppose anyone knows where the two big springs go?🙄

17258104287848390337748223729360.jpg


I can see that I need to replace a brush spring 👍
 
I've got a new "Smiths" heater motor here that I think I bought from Paddocks at some point.
Interestingly it seems to be made in China !
You're probably better off reviving your old motor if you can, it's probably better quality
 
grewth said:
I've got a new "Smiths" heater motor here that I think I bought from Paddocks at some point.
Interestingly it seems to be made in China !
You're probably better off reviving your old motor if you can, it's probably better quality
Click to expand...
I've managed to get a new old stock from P A Blanchard.
So hopefully it's of good quality 😃
 
You must log in or register to reply here.

Similar threads

G
Series three heater matrix blowing cold
Replies
11
Views
1K
Citizen Kane
C
H
Looking for info on Relays
Replies
9
Views
425
lynall
L
300tdi Tango
Heater blower motor replacement.
Replies
6
Views
910
300tdi Tango
300tdi Tango
R
Discovery 2 blower NipponDenso vs Bosch
Replies
3
Views
533
sierrafery
sierrafery
Jazydave
Blower fans
Replies
12
Views
961
Datatek
Datatek
Back
Top