Re: Wanted Cylinder head for 1991 Mazda b2600

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
A

automan

Guest
You do realize that the 2.6 is a Mitsubishi engine don't you? That engine
was a major headache.

"Kipp" <[email protected]> wrote in message
news:[email protected]...
> Need a cylinder head for 1991 Mazda B2600 with the 2.6L engine. Auto
> trans. If anybody has one or knows of one, I sure would appreciate
> info on it. I am located at zip 94560.
>
> My email is [email protected] (remove the nospam to email.)
>
> thanks,
>
> Kipp


 

"automan" <[email protected]> wrote in message
news:[email protected]...
> You do realize that the 2.6 is a Mitsubishi engine don't you? That engine
> was a major headache.

How so? My 92 Maz has 98K miles and is still going strong?

-CB


 
I used to work on them quite often. If it's a carb engine the carbs are
nightmares with a plastic-like body, choke & idle problems. I believe they
were known for head & head gasket problems also. Another thing with Mitsub
parts, they were usually a little more expensive than other jap parts. I
think the 2.6L was just in the 4x4's.

"Cyberbilly" <[email protected]> wrote in message
news:[email protected]...
>
> "automan" <[email protected]> wrote in message
> news:[email protected]...
> > You do realize that the 2.6 is a Mitsubishi engine don't you? That
engine
> > was a major headache.
>
> How so? My 92 Maz has 98K miles and is still going strong?
>
> -CB
>
>


 

"automan" <[email protected]> wrote in message
news:[email protected]...
> I used to work on them quite often. If it's a carb engine the carbs are
> nightmares with a plastic-like body, choke & idle problems. I believe they
> were known for head & head gasket problems also. Another thing with Mitsub
> parts, they were usually a little more expensive than other jap parts. I
> think the 2.6L was just in the 4x4's.
>
Mine is injected. I did have the head gasket replaced under warranty at 30K
miles, but haven't had any engine problems since. The worse problem I have
with it is I keep busting the CV joints in the front half-shafts but this is
probably due to abuse rather than an inherent defect.

BTW, know of any good sources for performance equipment for the pre-Ford
Mazda trucks?

-CB


 
Not right off hand. Sorry.

"Cyberbilly" <[email protected]> wrote in message
news:[email protected]...
>
> "automan" <[email protected]> wrote in message
> news:[email protected]...
> > I used to work on them quite often. If it's a carb engine the carbs are
> > nightmares with a plastic-like body, choke & idle problems. I believe
they
> > were known for head & head gasket problems also. Another thing with
Mitsub
> > parts, they were usually a little more expensive than other jap parts. I
> > think the 2.6L was just in the 4x4's.
> >
> Mine is injected. I did have the head gasket replaced under warranty at
30K
> miles, but haven't had any engine problems since. The worse problem I
have
> with it is I keep busting the CV joints in the front half-shafts but this
is
> probably due to abuse rather than an inherent defect.
>
> BTW, know of any good sources for performance equipment for the pre-Ford
> Mazda trucks?
>
> -CB
>
>


 
On 3 Jul 2003 23:26:06 -0500, "automan" <[email protected]> wrote:

>Not right off hand. Sorry.
>
>"Cyberbilly" <[email protected]> wrote in message
>news:[email protected]...
>>
>> "automan" <[email protected]> wrote in message
>> news:[email protected]...
>> > I used to work on them quite often. If it's a carb engine the carbs =
are
>> > nightmares with a plastic-like body, choke & idle problems. I =
believe
>they
>> > were known for head & head gasket problems also. Another thing with
>Mitsub
>> > parts, they were usually a little more expensive than other jap =
parts. I
>> > think the 2.6L was just in the 4x4's.
>> >
>> Mine is injected. I did have the head gasket replaced under warranty =
at
>30K
>> miles, but haven't had any engine problems since. The worse problem I
>have
>> with it is I keep busting the CV joints in the front half-shafts but =
this
>is
>> probably due to abuse rather than an inherent defect.
>>
>> BTW, know of any good sources for performance equipment for the =
pre-Ford
>> Mazda trucks?
>>
>> -CB
>>
>>
>

=46or a stock rebuilt head try

http://www.enginepartswarehouse.com/

=46or performance parts try

http://www.importperformanceparts.net
 
You must log in or register to reply here.

Similar threads

P
Re: Wanted Cylinder head for 1991 Mazda b2600
Replies
0
Views
987
pete selby
P
Back
Top