Hose clamps

Lumby84 · Jun 3, 2020

Hi All, sorry if this is a stupid question.

I have recently bought some silicone hoses for my defender 300tdi and am going to get some Mikalor Supra Hose Clamps (T-bolts) but i am unsure of which to buy as they only look to have a small tightening tolerance of a few millimetres.

I have measured the diameter of all the hoses and some of them are right on the limit of the clips.

For example: The diameter of the hose is 25mm and the hose clamps come in either 23mm to 25mm or 25mm to 27mm.

Should I go for the ones that tighten to the hose diameter or the ones that start at the hose diameter and go smaller??

Sorry if it’s a stupid question, it’s just they are not cheap and don’t want to get wrong ones.

Cheers.

Flossie · Jun 3, 2020

Consider stainless steel jubilee clips?
Fitted them to mine 16yrs and they still undo like they are new.

Lumby84 · Jun 3, 2020

Flossie said:
Consider stainless steel jubilee clips?
Fitted them to mine 16yrs and they still undo like they are new.

Yeah I might end up doing that going to cost up both options plus with jubilee clips the is a larger tightening tolerance.

Cheers

tottot · Jun 3, 2020

Flossie said:
Consider stainless steel jubilee clips?
Fitted them to mine 16yrs and they still undo like they are new.

Stainless jubilee's are good. They also tend to be wider than standard, spreading the load over the hose surface.

lynall · Jun 3, 2020

Mikalors are nice, but as you are finding a pita to size up.
There are cheap copy ones on ebay, but tbh you cannot really beat the good old jub clip.

v8250 · Jun 3, 2020

Mikalor hose clamps are first rate components, but so are the ASH equivalent...I buy mine here as they are correctly priced and have the full range in stock https://www.autosiliconehoses.com/ash-t-bolt-hose-clamps-stainless-steel-single-clip.html

The advantage with T-clamps is that they spread the clamping load over a wider hose area :. less pinch point and an evenly spread/better clamping. Just remember to lubricate when installing

lynall · Jun 3, 2020

v8250 said:
Mikalor hose clamps are first rate components, but so are the ASH equivalent...I buy mine here as they are correctly priced and have the full range in stock https://www.autosiliconehoses.com/ash-t-bolt-hose-clamps-stainless-steel-single-clip.html

The advantage with T-clamps is that they spread the clamping load over a wider hose area :. less pinch point and an evenly spread/better clamping. Just remember to lubricate when installing

Thank you, I knew there was another make and have been googling ADS ADS, but NOT ASH, back to ebay.

Sweet half the price of Mikalors.

Lumby84 · Jun 3, 2020

Cheers all, really appreciate the advice. Thanks

nobber · Jun 3, 2020

If you buy Jubilee clips make sure they are jubilee clips, anything else is just made from chocolate.

https://www.jubileeclips.co.uk/

lynall · Jun 7, 2020

New clips fitted, W4 spec, very nice, 10 for 21 quid, same in Mikalor was best part of 60 quid.

Hose clamps

Lumby84

Member

Flossie

Well-Known Member

Lumby84

Member

tottot

Well-Known Member

lynall

Well-Known Member

v8250

Well-Known Member

lynall

Well-Known Member

Lumby84

Member

nobber

Well-Known Member

lynall

Well-Known Member

Similar threads