Officerdibble
Member
- Posts
- 75
- Location
- Northwich
Anyone know where I might be able to get some female electrical terminal connectors which slot into the back of the interior fuse box in a 300tdi
cheers
cheers
Fuse box
- Thread starter Officerdibble
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Speckydude
Well-Known Member
- Posts
- 1,599
- Location
- Tome
RS ?
Officerdibble
Member
- Posts
- 75
- Location
- Northwich
Sorry for the ignorance but who's RS
Speckydude
Well-Known Member
- Posts
- 1,599
- Location
- Tome
Used to be called Radio Spares, now they are called RS, look for them on the internet.
Are these the sort of thing you mean ?
https://www.lrworkshop.com/connectors/defender-1996-300tdi/C907
Speckydude
Well-Known Member
- Posts
- 1,599
- Location
- Tome
Officerdibble
Member
- Posts
- 75
- Location
- Northwich
No I've got the dash out at the minute and there's a couple off wires with inline fuses next to fuse box just wanted to tidy it up a bit and put em into the spare locations on fuse box
Speckydude
Well-Known Member
- Posts
- 1,599
- Location
- Tome
Ah ok .
Rougharse Racing
Well-Known Member
- Posts
- 883
- Location
- The Grim North
I know where to get them and what to use, but you were so arsey with my response to your oil pressure post, you are on your own with this one,
mick the builder
Well-Known Member
- Posts
- 5,901
- Location
- Sligo,Wild West of Ireland.
Note to self, do not respond unfavourably to rougharse.
Officerdibble
Member
- Posts
- 75
- Location
- Northwich
Omg let it go mate...
For the 300Tdi interior 20-way fuse box (pictured below)
You need this type of terminal -
Available here -
https://www.3waycomponents.co.uk/Fu...male-Uninsulated-Fuseholder-Terminal-51101980
.
Officerdibble
Member
- Posts
- 75
- Location
- Northwich
Cheers PaulFor the 300Tdi interior 20-way fuse box (pictured below)
You need this type of terminal -
Available here -
https://www.3waycomponents.co.uk/Fu...male-Uninsulated-Fuseholder-Terminal-51101980
.
Can any one give me some ideas re my heater. I have an ex MOD- 1996 - Defender 110 - A2 Snatch. The blowers work but no heat comes out. The heater lever control is right down but only the slightest of heat coming out. Heating virtually non existent and now the frost is coming need some heat.
- Posts
- 12,068
- Location
- Far out West
Check under the bonnet on top of the heater box, the two cables work two arms. Make sure the cable is moving the arm fully
- Posts
- 1,205
- Location
- The Flat lands of Cambridgeshire
my 86 90 was like that,
had the top of the dash off and checked all the pipes and vents were intact.
also eventually found my problem was knackered heater matrix, but new seal was a b***er to fit
Mine is certainly better now, also the fan needs to be flat out or you get nothing on early models
Have heard tales of loads of rubbish being pushed into vents and ex mod one no telling's could have put something in the pipe for fun,,
AM sure i heard somewhere, maybe even on here, someone found a cue ball from a pool table somewhere in the pipeworks
Good luck, certainly easiest starting point is
get an assistant to work controls while you watch.
had the top of the dash off and checked all the pipes and vents were intact.
also eventually found my problem was knackered heater matrix, but new seal was a b***er to fit
Mine is certainly better now, also the fan needs to be flat out or you get nothing on early models
Have heard tales of loads of rubbish being pushed into vents and ex mod one no telling's could have put something in the pipe for fun,,
AM sure i heard somewhere, maybe even on here, someone found a cue ball from a pool table somewhere in the pipeworks
Good luck, certainly easiest starting point is
get an assistant to work controls while you watch.
Similar threads
