Driver's side footwell hole spacings

Webley1991 · Mar 19, 2013

Does anyone have a bulkhead that is off the vehicle at the moment?

If so, I would like a measurement of the positions of the three square holes in the bottom of the driver's side footwell.

As in distance from the side, between each hole, and distace from the edge of the panel.

A friend repaired my bulkhead but forgot to put these in to the new panel. I will drill over-sized round holes and use bolts rather than square holes and captive clips.

Cheers
webley1991

crashbox · Mar 19, 2013

Are you looking for the pedal holes?...sorry, just re-read your question. Give me five minutes and I will have a look.

crashbox · Mar 19, 2013

Just had a look, they have been repaired with new panels in the past and have round holes. The spacings from the inner driver side wall/pillar are 87mm, 305mm and 493mm, all distances are from the pillar.

crashbox · Mar 19, 2013

I don't really see the problem though. Once you fit the bulkhead, place your floor panel on top, mark the holes and drill them out.

crashbox · Mar 19, 2013

:scratching_chin:

op2:

Webley1991 · Mar 19, 2013

Thanks for that.

The passenger side footwell still has the square holes. I would think that these should be the same distace in from the edge of the panel. About 30mm seems right from memory?

crashbox · Mar 19, 2013

Webley1991 said:
Thanks for that.

The passenger side footwell still has the square holes. I would think that these should be the same distace in from the edge of the panel. About 30mm seems right from memory?

I measured the holes on one of mine, distances are as above in mm.

crashbox · Mar 19, 2013

Unless you will be looking for a concours prize, it doesn't really matter.

Webley1991 · Mar 21, 2013

Sorry, I had another look at the bulkhead as I hadn't seen it for a while.

It is actually the PASSERNGER side footwell that is missing the holes.

Would you be able to post the spacing measurements for these?

crashbox · Mar 22, 2013

Webley1991 said:
Sorry, I had another look at the bulkhead as I hadn't seen it for a while.

It is actually the PASSERNGER side footwell that is missing the holes.

Would you be able to post the spacing measurements for these?

Yes, I will have a look on Saturday morning.

Webley1991 · Apr 7, 2013

Did you ever manage to get these?

Webley1991 · Apr 25, 2013

Anyone?

I need the hole spacings in mm for the PASSENGER SIDE footwell on a Series 3 bulkhead.

crashbox · Apr 25, 2013

Webley1991 said:
Anyone?

I need the hole spacings in mm for the PASSENGER SIDE footwell on a Series 3 bulkhead.

Give me 10 minutes M8ey.

crashbox · Apr 25, 2013

Okay, measured from the left inside edge of the footwell. First hole is 50mm from the left and 50mm from the edge of the panel nearest to the rear of the vehicle. Second hole is 85mm from the left inside edge and 20mm from the rearmost edge.Last hole is 300mm from the left inside edge and 20mm from the rearmost edge. Hope this makes sense, if not I can take a photo. This is a replacement panel.

The Mad Hat Man · Apr 25, 2013

that was 11 minutes ago - you was late

.

crashbox · Apr 25, 2013

The Mad Hat Man said:
that was 11 minutes ago - you was late .

Measurements were taken in 10 mins but it took one min to type it up and I pm'd him with the results in 10 mins, so there Mr pedantic.

Webley1991 · Apr 26, 2013

Thanks for the reply. It seems that the hole spacings in the passenger side floor aren't the same as this. I will simply put the floor in place and drill through the holes when it comes to it.

Driver's side footwell hole spacings

Webley1991

Well-Known Member

crashbox

Well-Known Member

crashbox

Well-Known Member

crashbox

Well-Known Member

crashbox

Well-Known Member

Webley1991

Well-Known Member

crashbox

Well-Known Member

crashbox

Well-Known Member

Webley1991

Well-Known Member

crashbox

Well-Known Member

Webley1991

Well-Known Member

Webley1991

Well-Known Member

crashbox

Well-Known Member

crashbox

Well-Known Member

The Mad Hat Man

Well-Known Member

crashbox

Well-Known Member

Webley1991

Well-Known Member

Similar threads