the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
The yoke on my front prop has decided to self destruct so I'm looking for either just the yoke on its own or a whole prop if anyone has one going spare? Ta muchly
Defender 300tdi complete prop or yoke
- Thread starter the_wolf
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Jonnyb1990
Well-Known Member
- Posts
- 2,013
- Location
- Gloucestershire
I've got a spare front prop from a D1 if you want it,
Only issues is that one of the UJ's is seized/stuck as its covered in gunk, and it isnt contracting again (tried replacing a gaiter which wouldn't fit)
Only issues is that one of the UJ's is seized/stuck as its covered in gunk, and it isnt contracting again (tried replacing a gaiter which wouldn't fit)
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
It's just the yoke I need mate. Where bouts are ya?
- Posts
- 10,639
- Location
- Oxfordshire
you been hitting wet grass again?
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
I wish. Decided to die on the dual carriageway. Prop is fine but the yoke ain't, oh and the floor and the chassis rail...
- Posts
- 10,639
- Location
- Oxfordshire
oh it bounced? that could have been nasty.
d1 300tdi front, as above, is the same thing btw
blue beasty
Leaks an prone to bits dropping off
- Posts
- 62,708
- Location
- Gloucestercotshirewolds
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
See I could do that, but I is on my phone and it doesn't show locationYou could try looking at their location.......might be a clue
Jonnyb1990
Well-Known Member
- Posts
- 2,013
- Location
- Gloucestershire
South west (Glos)
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
It could have been, damage wasn't too bad. Let go at 60 too.oh it bounced? that could have been nasty.
d1 300tdi front, as above, is the same thing btw
Ah that's a fair distance away, postage will be extortionate
Jonnyb1990
Well-Known Member
- Posts
- 2,013
- Location
- Gloucestershire
not so fussed about you buying it, you can have it for nothing,
Postage however i'm not so sure on
Postage however i'm not so sure on
ronsealdeath
Sagging Member
- Posts
- 1,851
- Location
- Swansea, Wales
Take care switching the yokes, apart from the obvious alignment, the whole prop may need a re-balance afterwards anyway. Probably best to source a complete prop and just fit new UJs? I have two front props in my garage from a Disco 300; you can have one if your passing Swansea!
Cheers
Cheers
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
I'll give it a miss mate, thanks anyway. Postage probably wouldn't be worth it and ive managed to source one closer.
Good old vilguy has one, just hope the flanges fit. It's a double cardan for a disco but should be ok
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
This is the one vilguy has for me. Do y'all reckon it'll fit?
vilguy
Do'er of stuff and the like
- Posts
- 9,915
- Location
- Dumfrieshire
its off a disco td5
- Posts
- 10,639
- Location
- Oxfordshire
you just after the end flange? i have a rear 300 disco one. i'm sure one side is a normal flange, the other a rubber doughnut... hmm i might actually have a spare front 300 prop
- Posts
- 10,639
- Location
- Oxfordshire
yup, i have a spare 300tdi front prop and a 2.5na (same as 200 iirc) one. ujs are old but don't seem to have any play.
pm if you are interested
pm if you are interested
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
Anyone able to clarify on the compatibility of the flanges above? Just to clarify it's to fit a fender 110 300tdi with an R380 gearbox and usual tranny. Diffs most likely later 24 spline. Flange at sliding joint end is not a problem I would imagine, it's the other I'm curious about
