Bosch VE FIP

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
T

Troyyz

Member
Posts
41
Location
Paignton, Devon
Hi, Just enquiring if it is possible to change the top O,ring type seals at the top of the FIP easily?
mine is pouring as much diesel out through seals as into engine, though still running!
 
Thanks Tomcat,
as they say at Tesco, "Every little helps"!
Is there an alternative to the correct socket,(Triangular)anti-tamper screw?
Regards,
Troy
 
Hi Alan........
Think I may need to change whole pump, (easier) Just been and looked, and also leaking from Hi pressure, (Delivery/Distributor) unit also, so looks like most seals have failed at once! 165,000 miles, have another unit from a 40,000
525 diesel Beemer!
Thanks for help
Troy
 
Troyyz said:
Hi Alan........
Think I may need to change whole pump, (easier) Just been and looked, and also leaking from Hi pressure, (Delivery/Distributor) unit also, so looks like most seals have failed at once! 165,000 miles, have another unit from a 40,000
525 diesel Beemer!
Thanks for help
Troy
Click to expand...
The pump from the beemer may or may not fit as the flange diameter may be different. Even if it does fit, the electronics in he top will not be compatible with the P38 EDC.
 
Hi Datatek,
Any chance you can expand on what you say?
Spoke to Bosch tech earlier, and they said pump is identical,
Certainly looks it!
Regards,
Troy
 
It must have part number 0460406994 stamped on it or it will not work on a Range rover. Some BMW and Vauxhall pumps will mate to the flange, but as was said earlier you will need to swap the centre section upwards over. A pretty pointless exercise. You may as well strip your old pump and fit seals, getting the centre section back in the correct place can be a pain in the butt.
 
Think that mine has had a replacement engine at some stage, has BMW on rocker covers?
(A mate said normally has Land Rover on!)
Gave them engine No. - They said should be ok even down to electrics,as I had read somewhere that designations A,B,and C were used for settings?
 
all the p38 diesels have bmw on rocker cover as they were supplyed by bmw but different spec to work better in the p38
 
Many thanks to all for their input,(Brian,Wammers,Datatek,Alan and Dave)
going to try renewal of seals tomorrow,(Watch this space! lol)
Given me the confidence!
In the words of Arnie, "I'll be back!
 
biketeacherdave said:
tbc.1998 | eBay

this is the guy i use give him a call tell him what pump you have and he will supply you with the correct reseal kit for a few pennies also

LAND ROVER DISCOVERY 1 300 tdi Bosch VE injector pump head seal VITON Seal | eBay

injector head seal get a spare just incase you pinch the first one when reseating the injector head
Click to expand...

You really need to know what you are doing to replace the head seal hope he knows how to do it. If the spacer drops it pump out.
 
When Dopey did his pump the 2 seals for the top and middle had gone. There are a further 2 seals: 1 each side. By the time you've done those you'll probably have cured it.

If you don't get everything lined up EXACTLY as it was it can be a total bar-steward getting it back again. Learnt that over the weekend ...
 
You must log in or register to reply here.

Similar threads

Rubberknees
Injected quantity
Replies
5
Views
542
RangeRoller dt
RangeRoller dt
ar1g3
P38A Which EAS repair kit to get?
Replies
18
Views
1K
Grrrrrr
Grrrrrr
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
jimmacD
Back to the P38 house of pain!
2
Replies
21
Views
2K
Grrrrrr
Grrrrrr
J
P38 DSE FIP issues
Replies
6
Views
1K
stemac33
stemac33
Back
Top