A rust-free RRC!
- Thread starter Sebrof
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
AllanWorms
Well-Known Member
- Posts
- 345
- Location
- Whangarei, NZ
Looks like it's been used as a submarine!
norseman
Well-Known Member
- Posts
- 3,259
- Location
- Essex - UK
I must confess the decker panel has never been removed on my '87 so I don't know what it's like in there. I always press a length of black flexible tubing into the gap between the rear edge of the bonnet/hood & the decker panel to act as a seal preventing rainwater from filling the cavities where the bonnet hinges reside. I've often considered enlarging the (so called) drain hole on each side to allow insertion of an endoscope, but never seem to get around to the job.
Maybe subconsciously it's a case of 'ignorance is bliss'
Maybe subconsciously it's a case of 'ignorance is bliss'
Last edited:
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
Looks like its time to fire up the mig
- Posts
- 12,628
- Location
- Sud ouest France !
Think of the fuel economy with all that weight reduced
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Gas axe more likeLooks like its time to fire up the mig
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
norseman
Well-Known Member
- Posts
- 3,259
- Location
- Essex - UK
Now now its a classic so worth saving
Every Classic is worth saving, just a case of how dedicated/skilful the restorer is
And how deep his pockets are! I'll be a bloody wizard with the welding gun after all the holes been patchedEvery Classic is worth saving, just a case of how dedicated/skilful the restorer is
- Posts
- 12,628
- Location
- Sud ouest France !
And chief fabricatorAnd how deep his pockets are! I'll be a bloody wizard with the welding gun after all the holes been patched
myfirstl322
Well-Known Member
- Posts
- 41,354
- Location
- Hoots mon...
A wee inspirational vid...
yep they are rusty hoors of things, lucky they look so nice or else I'd send the thing to the scrappy!
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Wow. How long did that take to film / edit?!
To be fair ot wasn't that bad an example to start with.
myfirstl322
Well-Known Member
- Posts
- 41,354
- Location
- Hoots mon...
Gasless mig by the look of it, filthy process.
Interesting watch. Many of the same areas I've done on mine!
Definitely gasless mig. Has its uses, but much prefer gas & it looked like a lot of his work was inside.
Shame he didn't remove the rubber strip when he painted the quarter panels - easy with a piece of strong fishing line or electric wire & refit with double sided number plate tape.
Definitely gasless mig. Has its uses, but much prefer gas & it looked like a lot of his work was inside.
Shame he didn't remove the rubber strip when he painted the quarter panels - easy with a piece of strong fishing line or electric wire & refit with double sided number plate tape.
Last edited:
And if you haven't already found them there are several companies that do repair items for the Classic.
Home - YRM Metal Solutions (yrmit.co.uk)
Froggatts Land Rover & 4×4 Specialists of Bosley, Macclesfield, Cheshire, UK
I've had a couple of bits from the latter, the last being the rearmost body-to-inner-sill mount which came with a new bushing & bolt & I was very impressed.
When I'd replaced the other side a few years previously I'd fabricated it myself. Having now used the Froggatts one I'd have one of theirs every time.
Dremel with flexible extension and the reinforced cutting discs was excellent as there's no room for a full size grinder.
Home - YRM Metal Solutions (yrmit.co.uk)
Froggatts Land Rover & 4×4 Specialists of Bosley, Macclesfield, Cheshire, UK
I've had a couple of bits from the latter, the last being the rearmost body-to-inner-sill mount which came with a new bushing & bolt & I was very impressed.
When I'd replaced the other side a few years previously I'd fabricated it myself. Having now used the Froggatts one I'd have one of theirs every time.
Dremel with flexible extension and the reinforced cutting discs was excellent as there's no room for a full size grinder.
Jayridium
Well-Known Member
- Posts
- 1,416
- Location
- Pedronapper (Peterhead)
That's almost as rusty as the disco I restored 5 years ago...
Hello Forggats, which repair panels do you need? - YES!
Hello Forggats, which repair panels do you need? - YES!
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Wow it's barely even that much of a rotten piece of shít.
