I have fitted original equipment pre-facelift headlamps. MOT tomorrow, fingers crossed.

The LED headlamps were installed by a previous owner. I understand that fitting of LED bulbs is an issue, but fitting of complete headlamps is acceptable. MOT rules say headlamp leveling must work if fitted, which it is not anymore. The vehicle still has air suspension fitted which I assume will...

My son's Disco 2 td5 has failed the MOT because the headlamp adjusting does not work. The headlamps have been replaced with LED headlamps which do not have headlamp leveling motors installed. Can I just remove the headlamp adjuster switch inside the vehicle and fit a blanking cover in it's...

I contacted Ring, who manufacture the deflectors that we have. They have emailed instructions for these headlights, so that is sorted. One of the rings that holds the headlights in place is corroded. Got a pair online but they are slightly too big. Do the 7" round LED headlights that gstuart...

The vehicle has passed the M.O.T at least twice with these lights fitted. I will check for "E" marks.

Of course the headlights are after market. Has anyone had this issue and if so what did you do?

My son's R/H/D Discovery 2 is fitted with LED Halo headlights. He is taking it to France. He has bought headlight deflectors, but the instructions do not include how to fit them to LED headlights. Should he fit them to LED's or do the LED's have a flat beam with no spike? If he should fit them...

Thank you, I thought that might be the case. Don't see what difference 3 BHP would make. Ebay seems to be wrong.

I need a replacement rear hub for my son's 2002 Disco 2 136 HP. Ebay says that part number TAY100050 is not suitable. They only seem to have hubs for 139 HP. Is there really any difference, can I fit a rear hub for a 139 HP? Any advice PLEASE.

No they will not unlock from the C.D.L switch. I have now plugged in a second hand latch which will unlock, so it seems that I need to replace all of the latches. I am confused as to what makes the sound when unlocking with the faulty locks. I assume the actuators are trying to work, but are too...

1998 Disco 2. All the doors and boot will lock with the remote, but only the boot unlocks with the remote. When unlocking with the remote all doors make the clonking sound of unlocking but do not. This has always been like this since my son bought it a couple of years ago. I don't think single...

Yes the fob does not work at all. I have read something about ground problems under the roof lining??

My friends 2001 Disco 2 TD5 will not start. He returned to his Landy, started it up, moved it, turned it off, put some luggage in the vehicle & then went to start up, but it will no longer start. The red immobilizer light is on when trying to start. We have tried programming a key from another...

Thank you all for your comments. I have removed the alternator again & checked the brushes that I fitted, they look fine & only a very small amount of oil within the casing. My son fitted the battery & I noticed the terminals were slightly loose, but Landy started up first time every time after...

Alternator stopped charging intermittently, Replaced alternator brushes which had been effected by oil ingress. Replaced the battery, which had a faulty cell. All seemed well after this initially, but now ignition warning light staying on again. I thought that even with oil ingress that it would...

Yes my son updated the Foxwell when he registered it. I think the memory card is 8GB.

We bought a Foxwell NT520 £130. It reads the DTC's & will clear them, but live data only lasts for about 10 seconds & them suffers communications failure. Has anyone else had this problem & is there any advice on why this happens please??

We have bought a Foxwell NT520, checked the DTC's & found shuttle valves open circuit. After replacing the shuttle valves & carrying out the on-line mod, cleared all DTC's, none have returned & 3 amigos out at last. Is it safe to assume that the new hub we fitted must have the correct number of...

No way can we afford genuine parts. We got it on ebay. I have checked the wheel speed sensor output again. This time the left hand front is 3.20volts ac. The others are still around 1.1volts ac. Why is the left hand front sensor now reading higher than the others?????? Any advice greatly...

We have now replaced the hub but the 3 amigos are still on. We will have to get the DTC's read again. Previously we had a shuttle valve fault code, we checked the mod that had been done & fitted better quality heat shrink connectors but there could still be a problem there.