Well alls well. Was a faulty solenoid. The box is working very smooth and no codes. Thanks Phil for all your help

Dropped the sump this morning Again nothing to be alarmed at 9x T27 bolts hols the plate that holds the solenoids These are a pain to get out as the oil is so slippy and its tight at the rear of the box The plate comes off no tight fit so you can pull any solenoid Pull solenoid c or mv3 on...

What a job trying to get hold of one of those solenoids. You need the full plate info on the side of the box and then it's not clear as zf don't describe them as shift solenoids Anyway got one for around the £70 mark. Would have got one from Phil but as above he's in Malta He needs a...

Happy Maltese break Tell you how it's gone when you get back

Those pins are tiny so might try again tomorrow if I get chance. My eldest gets his gcse tomorrow ✌️

It was taken with it off the ecu Serial number 0483086 Model number 000032 I e sent you a pm Phil about another matter

If you buy a rangie then you need to buy a good code reader. It's not an option unless you like forking out £50-£120 a time for a garage to reset or diagnose problems £80-150 will get you one that reads gearbox and air bags and abs Worth its weight in gold and keep it in the car

How olds the pump. It won't sense any increase if it's not pumping air out

Phil many many thanks Plugged in the data reader to see anything on the next trip out when it had cooled and not showing fault. Nothing I could see as my reader is not that good but it was showing valve 3 always off whilst the other 2 changed from on off as I was manually changing gear I went...

Ok filled her up and shifted the gear lever forward back and in the manual selection then waited to warm up and filled her to the top Test drive First impressions very smooth no problems. But then the trans safe mode came back in Took her home sat on drive for 1/2 hour after clearing fault...

Just got heads up the oils been delivered. Will be in touch after I've filled it

I've also taken off multi plug and put back as all the terminals looked ok on the gearbox It won't hurt to change the oil as you never know what those frenchies put in it

Thanks Phil. I have you stored in my contacts if it's a pull and mend job Yes it may be the battery or alternator I regularly check the volts out and it as it should be and the battery was New at the start of the year I will check again if it is around the 14 v on load This may explain the...

Had this rangie since Jan. Has been running fine and has a fine very expensive history and has done 82k miles now all documented service history In 2010 on its way to Switzerland the gear box went and I have the bill for 5500 euros ouch !!! New box cooler and torque converter. That was...

No picture available

Did mine recently They has already been done 12 months earlier but leaked The oil separator was not in the best of condition and replaced with a new one The front cover gaskets were protruding upwards above the flat of the cam covers. I trimmed these down with a sharp nife, so it was...

I put sealant on mine to make sure. I also found the seals on the chain cover protruding so cut them down flat to make a flat surface Also make sure the pipes that go onto the pcv are on tight. For some reason the britpart pipe I recently purchased was short by about 3 cm so was as tight as...

No. Take off covers to coils and look at it in the dark. If it's arcing you will see it Could be a cracked exhaust manifold or tappet a tap tap tappin

No need to as they around the corner to me It's confused us all and the loom pins out as it should so sometime it's best just to bite the bullet It's like the l322 gearbox Simple if your doing it every day with the same problems, but not if you put a Kia box on the bench you don't know a lot about

Unfortunately the distributor in the uk folded a few months ago and Tinely tech has just become the importer so im trying to get hold of folks that are no longer there and Tinely tech do such a lot and its new to them Ive decided to go for a new emer kit with type 34 injectors and the instaler...