ukadamwest · Jan 10, 2015

Having done some work on both the P38 and the Classic and today having fannied about with the sunroof headlining panel for the better part of a couple of hours (dark stopped play) it got me to thinking..

The rave manual puts this as a simple task a couple of straightforward steps.. but ohhhh noooo ! never is that way.. it out annoys putting the sodding link rod end clips on the door lock mechanism and that caused a lot of 'grrr-ing'

So what's the biggest fanny about for what appears to be a s simple job that you've come across or had to endure on the range rover ??

wammers · Jan 10, 2015

None all the jobs are very easy.

ukadamwest · Jan 10, 2015

raise:

Well get yer northern backside down here and do my sunroof headlining panel then

wammers · Jan 10, 2015

ukadamwest said:
raise:

Well get yer northern backside down here and do my sunroof headlining panel then

Will be doing mine when weather gets better. Or when the time comes i can get enough **** out of the garage to get the car in.

ukadamwest · Jan 10, 2015

Or when the time comes i can get enough **** out of the garage to get the car in.

Still no inside toilets up north then ?

wammers · Jan 10, 2015

ukadamwest said:
Still no inside toilets up north then ?

Think you misinterpreted the meaning of the word ****.

Saint.V8 · Jan 10, 2015

ukadamwest said:
Still no inside toilets up north then ?

LMFAO :hysterically_laughi:hysterically_laughi:hysterically_laughi :clap2::clap2:

wammers · Jan 10, 2015

Saint.V8 said:
LMFAO :hysterically_laughi:hysterically_laughi:hysterically_laughi :clap2::clap2:

Don't you start.

tomcat59alan · Jan 10, 2015

Saint.V8 said:
LMFAO :hysterically_laughi:hysterically_laughi:hysterically_laughi :clap2::clap2:

Cheeky savern cants,

tomcat59alan · Jan 10, 2015

ukadamwest said:
Still no inside toilets up north then ?

I think you have answered your own question "what is the biggest fanny you have come across"

domino · Jan 10, 2015

Is there a guide for replacing the sunroof liner...without removing all the headlining?

ukadamwest · Jan 10, 2015

Is there a guide for replacing the sunroof liner...without removing all the headlining?

You don't need to remove the headlining to get to the sunroof panel, the roof itself and the headlining panel slides into a box, or tray, if you like, mounted in the roof, so removing the headlining gets you no more access to the panel.

P38

Classic

From Parts Catalogue here : http://www.allbrit.de/UNI.cfm?PAGE=830664&SPRACHE=EN

Hairy · Jan 11, 2015

Ive got a sunroof cartridge to put in when do the headlining, should be fun. :lol:

200tdi ayre · Jan 11, 2015

Range rover classic heater box

:flame2::flame2::violent:

odyssey · Jan 11, 2015

domino said:
Is there a guide for replacing the sunroof liner...without removing all the headlining?

I don't think it's really feasible, but there's a good photo guide to the job here:- Range Rover 4.6 HSE - Detailing World

That said if anyone knows different I'll be delighted to be proved wrong.

I'm probably going to have to do mine again before the summer . . .

A

aj1954 · Jan 11, 2015

For me it was LH blend motor retaining screws, access to motor easy airbag out, glovebox out, and lower panel off, I undid the screws using a pozi bit, longnose pliers, and a 7mm spanner, replacing em was harder, but Ive had an idea why not replace the screws with hex headed ones, then only spanner needed, some of you will probably disagree and say "piece of ****" just my thoughts.

fanatic · Jan 11, 2015

aj1954 said:
For me it was LH blend motor retaining screws, access to motor easy airbag out, glovebox out, and lower panel off, I undid the screws using a pozi bit, longnose pliers, and a 7mm spanner, replacing em was harder, but Ive had an idea why not replace the screws with hex headed ones, then only spanner needed, some of you will probably disagree and say "piece of ****" just my thoughts.

wammers · Jan 11, 2015

aj1954 said:
For me it was LH blend motor retaining screws, access to motor easy airbag out, glovebox out, and lower panel off, I undid the screws using a pozi bit, longnose pliers, and a 7mm spanner, replacing em was harder, but Ive had an idea why not replace the screws with hex headed ones, then only spanner needed, some of you will probably disagree and say "piece of ****" just my thoughts.

Proper tools piece of ****. Wiping your arse with grease proof paper is also difficult.

pete1987RRC · Jan 11, 2015

wammers said:
Proper tools piece of ****. Wiping your arse with grease proof paper is also difficult.

Was it called izal?

fanatic · Jan 11, 2015

pete1987RRC said:
Was it called izal?

Izal was banned due to health and safety- anus paper cut

Well-Known Member

No longer with us, RIP

Well-Known Member

No longer with us, RIP

Well-Known Member

No longer with us, RIP

Dyed-in-the-wool 100% RR Junkie

No longer with us, RIP

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Active Member

Well-Known Member

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

No longer with us, RIP

Well-Known Member

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

Similar threads