MoorlandBOB
Banned
drained the rusty water from the transfer box and put oil in instead lol...
THEengineer
whatever
one nut snapped off the lock stops,my fault,other ones looking fooked as well
THEengineer
whatever
least your disco dont rust as bad as a transit,just had all the cills on our 03 trannie rebuilt,and theres still loads of welding left underneath it
robint
Well-Known Member
wouldnt say that this is the third time and last time being cut off later in the summer
tom1disco.300
Active Member
weekly checks,oil,water, and airfilter,tires,steering box oil level,and wheel bearings,brake fluid and clutch fluid,oh and adjusting brakes constantly as they are just crap! haha
MoorlandBOB
Banned
gemsdad
NOT BOTHERED.
i personally would have set fire to both.....
still got your shed of a tratter then bob?
SnowmanV8
Well-Known Member
i personally would have set fire to both.....
Was going to but you didn't show up to throw on top. Every good bonfire needs a gay..... Erm I mean guy
Pikey
Dummy Ejection Facilitator..
just replace with noo bolts. if you have to much lock I:E rubbing use longer bolts.
Pikey
Dummy Ejection Facilitator..
no just align it so ya can get ya hands in to undo top and bottom retaining knobs. whole cluster can then be removed from outside of vehicle.
Grahame of the shires
Active Member
Drove up A1 to drop daughter of at a St Johns Ambulance camp. Then drove home only to be held up for 1/2 hour cos some stupid animals decided to use the road!!!!
rich290185
New Member
Fan belt ordered at lunch time,it came at 2 am i had it fitted by 2:30.
all the oils getting done tomorrow EGR kit ordered and i think ill get a timing kit ordered for next week
all the oils getting done tomorrow EGR kit ordered and i think ill get a timing kit ordered for next week
brian47
Well-Known Member
just replace with noo bolts. if you have to much lock I:E rubbing use longer bolts.
That's his plan apparently, just as long as he can get the old ones out!
So far he's busted the head off one and turned it into a stud, then he tried my Sealy stud extracter, didn't work so he tried a Stiltson and that didn't work so he tried a bigger Stiltson.
I think he's going to try some intense heat next.
If that fails I reckon he's going to have to drill the old ones out and retap the holes.
And yes, he assures me that he slackened off the lock nuts first.
decided to do a trial fit of the rangie classic rear seat for the station wagon......
first step was to measure n chop out a 10cm deep cut into the arch...
next I trimmed down the cut out section and riveted it to form a new 'side' panel.....
then I fabricated the missing metalwork from a thick galvanised shelf that I had 'liberated' some time ago..... sealed and riveted all round
then time for a trial fit of the seats.....
fits well at the rear also....
you sit at a far more sensible height... rear passengers can look through the window instead of the alpine lights lol.........
and you still have full folding capability so load space is still fully useable....
cheers steve
first step was to measure n chop out a 10cm deep cut into the arch...
next I trimmed down the cut out section and riveted it to form a new 'side' panel.....
then I fabricated the missing metalwork from a thick galvanised shelf that I had 'liberated' some time ago..... sealed and riveted all round
then time for a trial fit of the seats.....
fits well at the rear also....
you sit at a far more sensible height... rear passengers can look through the window instead of the alpine lights lol.........
and you still have full folding capability so load space is still fully useable....
cheers steve
Last edited:
HLRSeagull
New Member
Egr valve bypass done , removed valve and replaced top hose ....
New illumination bulb behind heater controls
New wiper blades
Adjusted handbrake up as needed too
And last but not least printed off London to Brighton application form to send off , this will be my first ever run but won't be camping on the Saturday
New illumination bulb behind heater controls
New wiper blades
Adjusted handbrake up as needed too
And last but not least printed off London to Brighton application form to send off , this will be my first ever run but won't be camping on the Saturday
