johnlad · Mar 10, 2012

played with the boost on my td5, flying now

andlover · Mar 10, 2012

on my d2 i changed all b-discks and pads, all brembo make

. that sorted my steering wheel wobling.

crashbox · Mar 10, 2012

Weld weld grind cut weld for 6 hours today.Welding on the chassis is done now.S3 may live again.

110woman · Mar 10, 2012

Got told last weekend that all the front seats in the beast come out - who knew

so today, took them out and cleaned 12 years worth of uuurrgg from underneath them

Ninja Haggis · Mar 10, 2012

110woman said:
Got told last weekend that all the front seats in the beast come out - who knew

so today, took them out and cleaned 12 years worth of uuurrgg from underneath them

Ok, how many Boiled sweeties and old sized 10p's ??

110woman · Mar 10, 2012

Ninja Haggis said:
Ok, how many Boiled sweeties and old sized 10p's ??

Found £2.60 in change and a carrier bag full of 'orribleness

90boy · Mar 10, 2012

110woman said:
Found £2.60 in change and a carrier bag full of 'orribleness

drinks are on you then

chunkymunky · Mar 10, 2012

Started project forward facing seats.

As you will see in picture...i hope, they wont fit to edge of tub. B n q i found 3mm by 30mm millrd steel lengths. Currently cutting and bending under heat to create a strong l shaped bracket which will fit to top of inner edge of tub and flat to wheel arch and bolted in. Seat bolts to that and wheel arch.

There is about 4inches of the seat overlapping the wheel arch but ok for occasional use. 3point seat belts too.

wiltshire landyman · Mar 10, 2012

replaced front and rear brakes fitted new starter motor,finally fitted aerial for the stereo

trax99 · Mar 10, 2012

finished fitting me inverter - wife then asked what does it do, is it a button for turning the car upside down?

RichP · Mar 10, 2012

Finally finished fitting the rear crossmember. Only the C post to do now and the welder can go away for a few months.

ScratchyDom · Mar 10, 2012

Fitted an air filter, temporary straps for now. A mate is going to fab me a custom stainless bracket...

And took off the cable tie holding up the fuel filter and bodged up a bracket, not too good but again a stainless one is on the way.

I'm particularly pleased with the colour coded stripe on the air pipe and the fact it's no longer inhaling all kind o' ****e.

Trewey · Mar 10, 2012

Used it to fetch 5 trailer loads of corded timber thinnings, ready to cut up and split into logs.

discomikey · Mar 10, 2012

replaced the wheelbearing that left me stranded at the side of the a518 yesterday. i had to replace the stub axle too.

then topped up the paint on my hubs, and started prep for painting the front end of it ready for the indoor 4x4 show.

ratty · Mar 10, 2012

emptied some more wood out of mine.

dirtyrhino · Mar 10, 2012

Filled it with junk for the tip run tomorrow, fixed the ****ty earth for the fan, adjusted the timing a smidge, found more crap to put in the back....

Fur Trapper · Mar 10, 2012

Trewey said:
Used it to fetch 5 trailer loads of corded timber thinnings, ready to cut up and split into logs.

How do you do that??????????split into logs Magic

or was that to be fire wood/stove wood

brock · Mar 11, 2012

made a new heavy duty bumper

easye1 · Mar 11, 2012

re tightend my drop arm nut wiv me new 34mm gun socket I bought.
tightened up the fanny belt,
and welded me drivers seat back together as it got embarrasin leaning while going round corners !

defender11069 · Mar 11, 2012

brock said:
made a new heavy duty bumper

very nice mate

Well-Known Member

New Member

Well-Known Member

Manky innards but smilin' still

New Member

Manky innards but smilin' still

Well-Known Member

New Member

Attachments

I’m back

Well-Known Member

Active Member

Well-Known Member

Cockernee, Pasty munchin bastid.

New Member

I'm not special I'm limited edition

New Member

Banned

New Member

Attachments

Banned

AKA Mr cool...

Similar threads