Sad innit?


I cleaned it.

12029d1256061428-what-have-you-done-your-landie-today-img_0552.jpg
 

Attachments

  • IMG_0552.JPG
    IMG_0552.JPG
    100.1 KB · Views: 240
i put a new outer wing skin on without removing the whole wing, should of taken off the wing tho would of probly been easyer.
 
redhand said:
Yu shud of undone the screws on the side of the rear quarter and fitted one of these Vehicle Aerial Mounts - Assorted Vehicle Mounts - : PSM-1 Rear/Side Mount with 5m cable with plug. Only a single skin if ally to go through. And yu'd have had no problems getting ya hand in to tighten the bolts and attach the coax. and there's loads of holes yu could have used to thread the coax thru into the vehicles interior
Click to expand...

That's exactly what I've got .. Gonna investigate at the weekend when I have time. Holes are through the outer and first inner, but didn't have a long enough drill to get through the third inner .. I just hadn't realised the side would come off.

I assume it'll be sealer'd on as well? Even if it is it'll be easier to do if I can get a hand in, I was looking at making a wobble headed socket .. ;)
 
Went for a spin in mine, 200 miles round trip and I drove it easy most of the time until some pillock annoyed me so I wound it up in third but chickened out at 75, she was still goin:eek:
Dont know what the mpg was, just enjoyed the day listening to the V8 burble mile after mile after mile.:D
 
Didn't do anything to my landy today other than drive it to work....

...where I took and passed yet another IT exam :D
 
Finished ply-lining the load area of me 110.

2nd row seats up / in use...

22-10-09_1423-1.jpg


22-10-09_1424-1.jpg


22-10-09_1425-1.jpg


2nd row seats folded down....

22-10-09_1418-1.jpg


22-10-09_1419-1.jpg


22-10-09_1420-1.jpg


22-10-09_1421.jpg


Me storage boxes fit perfick....

22-10-09_1427-1.jpg


The storage tray on the O/S wheel-arch lifts out, the one on the N/S is fixed.
 
Sorted out me dodgy n/s rear indicator... stuck some new bullet connectors on and a new connector block. That didn't work so tested bulb and it was fine, scratched me head a bit and poked about the o/s wiring to find that did the job. Renewed the connectors and block on that side just tae be sure. Then ah greased up me military tow jaw and swingaway wheel carrier.
Oh, and finally managed tae get the bus in the garage tonight fur the furst time after changin' the bulkhead.
before....

garage09002-1.jpg



garage09001-1.jpg



and after...

http://i266.photobucket.com/albums/ii264/bustersbus/S%20hitole/****ole001-1.jpg


http://i266.photobucket.com/albums/ii264/bustersbus/S%20hitole/****ole002-1.jpg

;):D:D
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
557
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
652
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
936
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
613
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
1K
invisible999
I