Yellow n black
ratty
I'm not special I'm limited edition
I was impressed with the speed I got up cheddar gorge. I left the slitty behind me in my dust.
ratty
I'm not special I'm limited edition
thought it was mine!
New Member
I was impressed with the speed I got up cheddar gorge. I left the slitty behind me in my dust.
thanks for telling me you was in cheddar you could of stopped at the sweet shop for me the only place i can get blackcurrant and liquorice twists. would of saved me bridge tolls
ratty
I'm not special I'm limited edition
thanks for telling me you was in cheddar you could of stopped at the sweet shop for me the only place i can get blackcurrant and liquorice twists. would of saved me bridge tolls
I'll try and remember to stop and get some for you next time I'm passing through. I'll even eat em for you if ya want.
It doesn't need an earth. It has a handbrake.
mikescuba
Well-Known Member
nickliv
Active Member
a2dds
Active Member
sounds like grub screw 's come loose on selector in top of box.
allows selector to wobble backwards and forwards. will only get worse
Oooo ****, don't like the sound of that, sounds important. When is it located and is it just a case of tightening it up?
Aidso
New Member
I know place that is very very good at fixing ECUs. Give me a shout if you want their details.
nrgserv
Well-Known Member
under the housing held on with 6 bolts, where the shaft goes in top of box.
lifts off when bolts out, grub screw locates in a hole in shaft.
disco bolts can be awkward to access, fender not sure about but floor easier to remove.
dunno which you have!
nrgserv
Well-Known Member
a2dds
Active Member
under item 3.
item 6 has the grub screw, item 4 has the hole.
Ooo ok so I just have to pop the cover off and adjust it?
monkfish24
Well-Known Member
My list since last weekend,
New door tops,
Cleaned out the hazard and fog light switch,
Fitted new numberplate,
Fitted new rear lights,
Cleaned, prepped and repainted rear cross member,
Unseized rear o/s wheel,
Fitted new rear O/s damper,
Cleaned and painted chassis around area.
Removed and cleaned indicator stalk connections.
Today's jobs:
remove rear wheels, clean and spray white.
Refit indicator stalk,
Replace rear n/s damper,
Clean and prep the chassis area around that for painting.
New door tops,
Cleaned out the hazard and fog light switch,
Fitted new numberplate,
Fitted new rear lights,
Cleaned, prepped and repainted rear cross member,
Unseized rear o/s wheel,
Fitted new rear O/s damper,
Cleaned and painted chassis around area.
Removed and cleaned indicator stalk connections.
Today's jobs:
remove rear wheels, clean and spray white.
Refit indicator stalk,
Replace rear n/s damper,
Clean and prep the chassis area around that for painting.
pontyslapper
Brought a Landy to LZ11. Yay!!
Dropped the tranny oil - all half a mugful!! Nowt suspect on the drain plug! :yay:
Replaced with noo 80/90 - much more funnily enough!
Also did same to front diff, lots more black stuff out, not watery, but nice and thick. Replaced with noo!
No leaks after a 10 mile pootle home from the yard - tranny lots quieter, but still jumped out of hi once - pondering looking at that grub screw mentioned earlier!!
Replaced with noo 80/90 - much more funnily enough!
Also did same to front diff, lots more black stuff out, not watery, but nice and thick. Replaced with noo!
No leaks after a 10 mile pootle home from the yard - tranny lots quieter, but still jumped out of hi once - pondering looking at that grub screw mentioned earlier!!
Decided to do rear wheel bearings.
Whilst stripping noticed pads were fubared and one of the wheel nuts was rounded (muppet at tyre place I reckon)
So nipped over to Craddocks for some pads and a few spare wheel nuts before carrying on.
Remembered to jet wash it first this time, much easier
Whilst stripping noticed pads were fubared and one of the wheel nuts was rounded (muppet at tyre place I reckon)
So nipped over to Craddocks for some pads and a few spare wheel nuts before carrying on.
Remembered to jet wash it first this time, much easier
