Paul D said:
Can you remember those ammo boxes someone picked a load up of? About 2 1/2' x 1' x 1' (about!!) .. I don't use mine now, do you want it?

I found a couple of Tesco delivery boxes, very strong, very light and much easier to move about .. :)
Click to expand...

Yes I collected a doz of em for the Southern LZer's . still got 3 of em that I dun't use.. :rolleyes:
 
timtheenchanteruk said:
made me a back door shelf for me caming stove

Just the right size for my lil stove & somwhere to put a pan next to it.

shelfclose.jpg

shelf1.jpg

shelf_stove.jpg

shelf_full.jpg
Click to expand...


That's not a stove :D I see ya went for the piano hinge then..
 
Replaced the a frame ball joint and refurbed the whole a frame while I was as it!
Absolute bitch of a job, everything was welded to the castings none of the bolts would come undone had to grind them all. Ball joint would come out, heat and press at 12tonne required!! Arm bushes needed heat and 10tonne!!!!

All done shiny and new now with a coat of hammerite to make it last and wow what a difference it's made! She drives like a new one!!!!!!
 
ant.7 said:
Replaced the a frame ball joint and refurbed the whole a frame while I was as it!
Absolute bitch of a job, everything was welded to the castings none of the bolts would come undone had to grind them all. Ball joint would come out, heat and press at 12tonne required!! Arm bushes needed heat and 10tonne!!!!

All done shiny and new now with a coat of hammerite to make it last and wow what a difference it's made! She drives like a new one!!!!!!
Click to expand...
good job:) it is one of the worst
 
Cleaned sump, fitted new turbo, fitted radiator, painted inside of bonnet and found the starter motors had it!
 
Fettled me bumpers.

Front, just cleaned it a bit with a wire brush and Hammerited some black on .. and painted the winch hook too, it just looked so rusty in front of all that black!

Bumpers06_zps4e2d8b58.jpg


Then set to to rid the rear bumper of the plastic End-Caps that constantly break and bend and to my mind are superfluous to requirements .. First I straightened the bumper so it at least looks almost straight .. it still isn't but wtf, it's close, and it'll likely only bend again, next time I'm near vertical. ;)

I then cut and ground the bumper ends flat so I could weld a plate over, wire brushed it all and hammerited it .. same both sides. Once fitted I wire brushed any other bits and hammerited them too, just to stop rust forming .. surprisingly few areas, the body cross member was great, the body mounts were forming surface rust, but nothing a quick blow over with the brush didn't cure!

Bumpers01_zpsf3cedf82.jpg

Bumpers02_zps31a2ea29.jpg

Bumpers03_zpsc5239d4b.jpg

Bumpers04_zps2aaf5934.jpg

Bumpers05_zpscf8ee473.jpg


Going to add a couple of reflectors when I get some, keep forgetting. I can't make my mind up whether it's better now or with end caps on, but I do know it's a tad stronger and less likely to catch.

DSCF0003_zpscb98ed82.jpg
 
discomark10 said:
good fix!
Click to expand...

Cheers.

Just seemed stupid to keep buying endcaps .. I've had three fronts replaced and four rears .. even after bolting them on instead of the self-tappers they still ripped off, or bent the frame ...
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
549
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
649
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
927
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
595
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
1K
invisible999
I