took hacksaw to errant front-bolt on starter motor
removed starter ..
removed broken regulator shaft from the h.p.pump
`````````````````````````````````````````````
replacement fuel-regulator n' starter motor on hand
nuts n bolts in various coffee jars since last year ..
hope i can remember which go with what part ;-]
`````````````````````````
`s`
 
Sold it... while i was enjoying the challenges it presented, it was the good wifes motor and it was time for her to move on.
Replaced with a 2016 F-Pace portfolio. different car altogether. i have to go and get a sim card for it!?!?
 
Never found a tyre centre that can put the steering wheel right!!
I took one car back 7 times and it was still wrong. Basic problem I think is that the road camber changes things from the flat workshop floor.

I use a digital vernier on the track rod ends to measure each side when tracking has been done, then simply add a mm one side and take it off the other side to centre the wheel and keep the tracking dimension.
 
andyfreelandy said:
Never found a tyre centre that can put the steering wheel right!!
I took one car back 7 times and it was still wrong. Basic problem I think is that the road camber changes things from the flat workshop floor.

I use a digital vernier on the track rod ends to measure each side when tracking has been done, then simply add a mm one side and take it off the other side to centre the wheel and keep the tracking dimension.
Click to expand...
Top tip Andy. I might try that at some point. I'll go back to the tyre fitters first though.
 
kernowsvenski said:
Now my steering wheel isn't central. Boooo.
Click to expand...

If the steering isn't straight, then this suggests they didn't adjust both sides equally, or didn't secure the steering wheel perfectly central when they did the tracking. There's no camber compensation applied to the FL1 steering, so on a highly cambered road, the wheel will be slightly off centre, but on a flat road, the wheel should be perfectly straight ahead.
I tend to fine adjust the wheel myself, as tracking places can never get it spot on. :(
 
Trying to decide whether to sell it to some other FL2 aficionado now, or wait a few months, by which time it will have the kudos of having done over 200,000 miles.:cool:

Or I might just keep it. :)
 
kernowsvenski said:
Finally got my new G015s fitted today. Hoorah! Had the tracking done too. Now my steering wheel isn't central. Boooo.
Click to expand...
I hate it when this happens, they obviously didn't do it properly, I had to Center it myself after getting it aligned at a so called pro outfit...
 
kernowsvenski said:
Never heard of it. I just Googled. It looks good value at about £75. It'll pay for itself if you use it twice. How accurate and robust is it?
Click to expand...
No complaints with mine. Accuracy is done to how precise you set it up. There's video's of how to use it on youtube.

Many years ago I couldn't find someone to do a full 4 wheel alignment, so I used a trackace on both front and rear wheels on my FL1. It's only for use on the fronts, but I put two perfect parallel fishing lines down the side of my hippo, and set the rears straight, then adjusted with the trackace anorl. Worked ok for me.
 
kernowsvenski said:
VCU bearings done today.
Click to expand...
Did you remove one of the rubber seals from each of the bearings & put some grease in ? The ones I got from Bell eng. (along with a vcu) only lasted about 5,000 miles !
I got another set (aftermarket) & removed a seal in each bearing to find next to no grease so I re-packed them with some decent high load grease & they've done 30,000 miles since without issue. (Might not be an issue if you used genuine hangers).
 
Some more trackace info I wrote some time ago. You only need the fishing line parallel lines if you want to adjust the rears.

https://www.landyzone.co.uk/land-rover/4-wheel-laser-allignment.181199/#post-2221160

ODFAqsy.jpg

DSCN2423 ODFAqsy
 
Andy Warren said:
Did you remove one of the rubber seals from each of the bearings & put some grease in ? The ones I got from Bell eng. (along with a vcu) only lasted about 5,000 miles !
I got another set (aftermarket) & removed a seal in each bearing to find next to no grease so I re-packed them with some decent high load grease & they've done 30,000 miles since without issue. (Might not be an issue if you used genuine hangers).
Click to expand...
I had a set supplied by Bell. One lasted about 10k, the other about 35k. The short life could have been down to alignment, or poor quality. No real way for me to know.

I did both today. Fitted GKN ones but didn't pack in any extra grease. I didn't want to move the seals.
 
You must log in or register to reply here.

Similar threads

T
Help!
Replies
13
Views
665
Nodge68
Nodge68
B
Freelander TD4 Mk1 Rear Diff - Does anyone have any advice on how to replace the rear diff?
Replies
1
Views
257
Freddie17
Freddie17
R
LED side lights not working
Replies
9
Views
733
RickyFreelander
R
C
Rear wheel bearings or diff
Replies
11
Views
1K
Nodge68
Nodge68
L
Freelander 1 2005 Land Rover Freelander 1 HSE - Loose Gear Selector in Automatic Transmission
Replies
3
Views
633
Hippo
Hippo