Drove my 2001 D2 back from down south to up't north, after a mud run and now got a strange squeak on the overrun and sometimes on the acceleration, if you accelerate hard it stops. Sounds clutch related, but going to check the propshafts as well. Sounds almost like a bird is living in there somewhere! I'm just glad I got back ok.
 
Last edited:
Easter clean inside and out, now sitting on four Pirelli Scorpions.

Started to use the D3 again for commuting within Cheshire, serving us well presently.

Happy Easter all 👍🏻
3C466DC2-66A4-4647-A7EE-6038B5043FE4.jpeg
 
Is that a sintered-bronze bush for the turbo-wastegate pivot ? Mine was sticky, so decided to lube it.
Hardest bit was removing the heat shield - two bolts above exhaust manifold were ok but the rear one was welded to the turbo. Luckily the rear part of the bracket was broken, so only had to drill out two rivets & it came off ok.
A 17mm spanner fits on that square end of the shaft to work it loose, so didn't need to remove the wastegate.
Used wd40/diesel/acetone mix to penetrate & free-off, then engine oil to lube it.
Must get a bit hot just there, is there a recommended lube for that level of heat... (?)
Not sure how long the oil will last, but next time I lose power at 2800 rpm I'll know to check this again...🤞
1712068016034.png
 
R-Two-D2 said:
Cleaned my MAP sensor, only cos I saw it somewhere on here... dunno if that mess was bad, or normal?
before & after pics... ('01 D2 td5 auto 129k)
View attachment 314096

View attachment 314097
Click to expand...
Well it's obviously better!
Is the lickle hole down inside it visible and clean?
Hope you din't stick anything down it and used sensor cleaner!
If it is OK it should drive a lot better!
Well done!
 
Stanleysteamer said:
Well it's obviously better!
Is the lickle hole down inside it visible and clean?
Hope you din't stick anything down it and used sensor cleaner!
If it is OK it should drive a lot better!
Well done!
Click to expand...
Yes it wasn't blocked so a cotton rag and elbow grease was sufficient.
What is sensitive inside the hole? :D
 
R-Two-D2 said:
Yes it wasn't blocked so a cotton rag and elbow grease was sufficient.
What is sensitive inside the hole? :D
Click to expand...
Here is a link to a thread of mine about this sensor, the problems I was having and why!
And how it got sorted!
www.landyzone.co.uk

Air flow logged low, IAT logged high.

Hi all, looking for help with a problem that only seems to occur when the engine gets really hot and/or when the weather is hot. Could this simply be that the MAP/IAT needs replacing? The Fault is that as I pull away from a standstill, i.e when lights change or when joining a roundabout, the car...
www.landyzone.co.uk www.landyzone.co.uk
Also to save @sierrafery some time here is a quote from him I found on another forum.
"Hi, the IAT is measured by the generally named "MAP sensor" in the intake manifold which actually has double purpose and gives both inputs(hence it's 4 wires), the sensor's protuberance is the IAT probe the MAP is the hole at it's bottom) the IAT is affected by EGR if you still have it fitted, a snorkel would have minimal to no effect on it as you said a bigger intercooler would lower it also the boost is important to be as high as possible"
from
 
Last edited:
A nice new set of genuine injector washers and o rings arrived .... Reading some posts, I've decided to do a full compression test whilst the injectors are out, to see if thats the cause of my smoke problems.... So, ordered the sykes-pickavant tool, that fits inplace of the injector, so I can check all cylinders, rather than using a glow plug adaptor. Will be doing my lads TD5 90 as well, so two for the price of one tester... I need to get my finger out of my anus, and get my Disco running again.
 
I just found there are petrol D4s on the market.
Will be looking at those when I next need to change! (if there are any left by then)
 
Pulled the door runners out to touch up, and discovered the carpet in both footwells was drenched underneath. Hours later I have the carpets out, and now the fun of leak tracing begins.
Frustratingly it's not as simple as the A pillar drain holes, they seem fine. But fortunately it's not red, so not the heater matrix...
 
R-Two-D2 said:
Must get a bit hot just there, is there a recommended lube for that level of heat... (?)
Not sure how long the oil will last, but next time I lose power at 2800 rpm I'll know to check this again...🤞
Click to expand...
Yes . There is. This is what I used on my ‘40. Not cheap, but good up to 1200C!!! Ignore the 140C, incorrect info… I checked.
 

Attachments

  • image.jpg
    image.jpg
    275.6 KB · Views: 11
  • image.jpg
    image.jpg
    256.8 KB · Views: 12
Been fitting a new condensing rad to the D2. Bracket bent slightly (easily straightend) out of the box which is a big improvement over the one Autodoc originally sent me as the whole rad. was curved (like a bike one) + the drier pipe was pushed into the core, only took them about 3 months to sort it !
 

Attachments

  • 20240620_102633.jpg
    20240620_102633.jpg
    456.5 KB · Views: 10
  • 20240620_102549.jpg
    20240620_102549.jpg
    184.1 KB · Views: 11
  • 20240620_102543.jpg
    20240620_102543.jpg
    124.3 KB · Views: 13
  • 20240620_102033.jpg
    20240620_102033.jpg
    405.3 KB · Views: 14
  • 20230925_124320.jpg
    20230925_124320.jpg
    280.6 KB · Views: 15
Shedload said:
Yea, I've had good and bad experiences with autodoc. Not sure they actually have some of the stuff they advertise.
Click to expand...
I must admit it's the only problem I've had with them. It, the 1st rad, was sent back next day, I left it for a couple of weeks & then started chasing them & it was always "we're waiting for our returns dept. to inspect it" Like you say probably had to wait to restock. (Didn't even get the first one out of its packaging & as the outer Autodoc box was undamaged it must of happened in the factory)
 

Attachments

  • 20230925_124420.jpg
    20230925_124420.jpg
    283.4 KB · Views: 7
  • 20230919_125635.jpg
    20230919_125635.jpg
    375.6 KB · Views: 9
  • 20230919_125444.jpg
    20230919_125444.jpg
    392.5 KB · Views: 7
  • 20230919_125428.jpg
    20230919_125428.jpg
    368.7 KB · Views: 6
  • 20230925_124300.jpg
    20230925_124300.jpg
    190.3 KB · Views: 10
Ordered from them 3 times, 1st time when I ordered, website said item available for dispatch. I ordered and paid for 48 Hr delivery, booked a day off. Then item Not available ! Arrived ten days later.
Last time, I ordered some cheap shocks for wife's KA. Followed delivery info' right up until it said out for delivery with my local driver, Geoff.
Then. 'returning to supplier'. No explanation. I asked why, they didn't know but I could pay the difference for some Monroe items.
To say I complained would be an understatement ! They sent the Monroe's at the same price. 😊
Rant over.
 
Oil& filter change whilst it's in bits for the condenser rad.
Noticed my latest Meyle filters are now chinky compared to last year's Austrian 🙄
 

Attachments

  • 20240621_110740.jpg
    20240621_110740.jpg
    312.5 KB · Views: 4
  • 20240621_104725.jpg
    20240621_104725.jpg
    404.2 KB · Views: 4
You must log in or register to reply here.

Similar threads

K
What money should I be asking?
2
Replies
27
Views
2K
Karls
K
F
What have you done with your series today?
Replies
4
Views
934
Frustrated Seriesist
F
L
SOLD - Land Rover Ninety (Defender 90) 300TDi Auto soft-top
Replies
9
Views
4K
mondifa
M
I
Disco 2 Central Locking Issue on a 1999 Disco 2
Replies
5
Views
799
sierrafery
sierrafery
R
Oh dear, what have I done......?
2 3
Replies
47
Views
5K
Rallymantony
R