Drove it (don’t tell) ;)

Hasn’t liked sitting there for weeks, started up fine with a little smoke but headboard has sagged down in the sun, not the lining, the actual board :(
May have to Defenderise the roof
 
Cleaned them

20200405_164600.jpg
 
Still haven't cleaned the outside of it yet.
IMG_20200405_181213_308.jpg

Wee man found the rear has cup holders I never knew it had them.
20200406_115726.jpg

Also ordered some osram night breaker laser d2s bulbs for it as they seem to be very highly spoken about in the headlight retrofit community.
Also bought the trims to tidy up my interior.
Number plate bulb blew so just ordered bulbs for everything inside and out.
Greased up the brake callipar sliders I was going to do discs and pads all round and handbrake shoes but they seem to be not that old and work fine anyway it also look like front to rear brake pipes have already been done so couldn't do that either.
Wire brushed the towbar and frame fresh black paint on that.
New alternator belt and ac belt.
Cleaned the map sensor since the m57 bmw cars seem to eventually clog them.
 
Salisbury Nick said:
This is how brakes should look after a bit of fun. Have you checked your guide pins? Mine have got stuck after days like that and need to be freed up.
Click to expand...
I did all the brake caliper pins in fresh grease one of the front pins had gone stiff. I did find the rear diff clunks when the wheels are turned in opposite directions but the front diff doesn't :eek:
 
Last edited:
Henry_b said:
My 2 P38's together..

m4bzpYkl.jpg


DIKY6fvl.jpg


What do ya'll actually use that rubber matt on the dash for?

I find it tries to fly off the dash with enthusiastic cornering.

Oh..

Added a floor matt too..

m40jFzEl.jpg
Click to expand...
My wife got me one of those models as a good luck charm since I went back to school. So far I have passed every test and I attribute that to Chance. Although they don't make them in Oxford Blue so she got me green.

received_542223393302597.jpeg
 
Last edited:
Check for lateral movement in the prop/diff

P38's short stubby pinon and (close bearings) aren't famed for their strength..
 
Henry_b said:
Check for lateral movement in the prop/diff

P38's short stubby pinon and (close bearings) aren't famed for their strength..
Click to expand...
The input shaft is solid, no up and down or in and out movement.
Ooer nurse... There's a little more play between the pinion and ring gear than I'd like but after 217.000mls it'll be a little slack. Both the front and rear diffs have the same play but the front doesn't make the same noise as the rear..
No noise on acceleration or deceleration either?
 
Last edited:
The H17 arrived... but something much worse happened. Turns out no one round here has a 50mm socket, and trying to use an F-Type resulted on much pain to my shin. This is going about as well for me as it did for RRDT...
 

Attachments

  • received_152684389447207.jpeg
    received_152684389447207.jpeg
    125.3 KB · Views: 123
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
1K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
533
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
717
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
797
Grrrrrr
Grrrrrr