C

Colin from Hull

Active Member
Hi, Came out of Tescos today and my Range Rover was sitting down (access height i think) at the rear, bouncing all the way home, front was ok. Just want heads up on the order of fault finding. I have had this problem before when left over Christmas, but seemed to sort it self out, on the way to work. Colin
 
Read Datateks How To in the How To section .... no special tools required!
 
Takes about 2 hours the first time. Personally I took the front wheel-arch liners out for ease of access rather than muck about.

J
 
Oh sorry, isn't he going to do them all?

If the rear ones are knackered the front ones will fail soon and you get get all 4 much cheaper.

J
 
I agree with Grrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr. Unless you replaced all 4 very recently, don't cheap out and only replace two. Do the whole lot and save yourself agro later on.
 
Grrrrrr said:
Takes about 2 hours the first time. Personally I took the front wheel-arch liners out for ease of access rather than muck about.

J
Click to expand...

Took me nearer 2 weeks ! (i)Top pins were well & truly rusted in (ii) after it failed to stay up I discovered a straight connector in the line which was leaking then (iii) i discovered my compressor was knackered.....
 
Hi, Havent looked at my car yet, its dark by the time i get home. Just an update, after i got home and tried my car again later, it just stayed on the stops, front and rear. The indicater light (Standard) just flashes. Does this throw any other ideas what could be wrong, is un-likely all four bags are faulty. Can i pipe in a pressure gauge to check output from compressor, then maybe at each bag. Colin
 
Colin from Hull said:
Hi, Havent looked at my car yet, its dark by the time i get home. Just an update, after i got home and tried my car again later, it just stayed on the stops, front and rear. The indicater light (Standard) just flashes. Does this throw any other ideas what could be wrong, is un-likely all four bags are faulty. Can i pipe in a pressure gauge to check output from compressor, then maybe at each bag. Colin
Click to expand...
Possibly an empty/low Air Tank level....

Run the engine and a leave a door open for ten minutes to recharge the tank, then close the door and select the standard ride height....with a charged tank it should pop up with a decent turn of speed....
 
Colin from Hull said:
Hi, Havent looked at my car yet, its dark by the time i get home. Just an update, after i got home and tried my car again later, it just stayed on the stops, front and rear. The indicater light (Standard) just flashes. Does this throw any other ideas what could be wrong, is un-likely all four bags are faulty. Can i pipe in a pressure gauge to check output from compressor, then maybe at each bag. Colin
Click to expand...

No air pressure. Do the compressor and diaphragm check in my "How To" at top of page.
 
Hi, Tried running car with door open, two lights on access/standard, after 10ish mins closed car door, standard light started flashing, then after a few seconds all four lights started flashing then message EAS FAULT. I will check compressor and diaphragm next. Thanks to everyone for your help. Colin
 
Colin from Hull said:
Hi, Tried running car with door open, two lights on access/standard, after 10ish mins closed car door, standard light started flashing, then after a few seconds all four lights started flashing then message EAS FAULT. I will check compressor and diaphragm next. Thanks to everyone for your help. Colin
Click to expand...

Fault is because rise has been commanded and nothing happened within the set time span. Bet it has no air.
 
Not 100% on air bag set up on LR but certainly on busses and trucks the air drying filer can cause this and with it being so cols a wet the now condensation is the first thing I would check
 
I'd work my way through Wammer's checklist, starting with the compressor test.

J
 
Ah, OK.

If the caps are platic and the pins pop straight out (I used an old wire coat-hanger) then about 2 hours taking your time to think about it.

If the pins are rusted in (probably ally caps) then you could be in for a longer stint.

To be fair, I sprayed my pins each night with WD40 until the weekend when I did the job. That might of helped?

J

TAKdriver said:
Took me nearer 2 weeks ! (i)Top pins were well & truly rusted in (ii) after it failed to stay up I discovered a straight connector in the line which was leaking then (iii) i discovered my compressor was knackered.....
Click to expand...
 
+ 1 on wammers check ,and you will still need to do at least the rear bags or it will just knacker the compressor again ,though as the others have said do all 4 and forget them for years :)
 
Grrrrrr said:
Ah, OK.

If the caps are platic and the pins pop straight out (I used an old wire coat-hanger) then about 2 hours taking your time to think about it.

If the pins are rusted in (probably ally caps) then you could be in for a longer stint.

To be fair, I sprayed my pins each night with WD40 until the weekend when I did the job. That might of helped?

J
Click to expand...

A lot better with Plus Gas.
 
You must log in or register to reply here.

Similar threads

M
Air suspension problems
2 3
Replies
59
Views
3K
Rubberknees
Rubberknees
M
Air suspension problems
Replies
1
Views
396
Datatek
Datatek
S
Height suspension / sensor issue - can't calibrate
Replies
3
Views
1K
Graculus
Graculus
Stev
suspension in extended mode and Suspension failure
2 3 4
Replies
68
Views
6K
Stev
Stev
J
Disco 3 (LR3) Air suspension fault
2 3
Replies
45
Views
4K
gstuart
gstuart