Bouch84

New Member
:rolleyes:Are the callipers on land rovers with solid disks (disco + defenders) the same as the ones with vented disks, or are they wider to accommodate the thicker disk? Basically could I shove a set of vented disks on my motor, which currently has solid disks?:confused:
 
You can put vented discs on your axles, but you will either have to buy new calipers or buy the spacer kit.

There is not much difference anyway, in braking efficiency.
 
as above, the discs are big enough to not make much difference.

Good quality pads, and braided hoses, with new fluid properly bled, now that makes a huge difference.
 
I had vented discs and calipers to suit for my 90 when I was rebuilding it and had to option to put them on, or stick with my original front brakes from my old axle, went for the originals because after a lot of reading and talking to people at the club I decided they didn't make any bloody difference unless I was planning on race towing down hills.
 
so i should sell that spacer kit i took out of those calipers i got off you disco? :) i was hanging onto them incase i wanted to do my 300tdi calipers and just buy the disks. so vented and drilled are no better than solid?

G
 
I would sell them yeah, I thought you took the spacers out and gave them to someone, must have been someone else.

You using those calipers now? I found out recently they had only done about 10,000miles, then sat on an axle for the rest of their life.
 
haha, well i was going to sell them, then i realised how much the kits were! so i hung onto them thinking i would only need to source 8 longer caliper bolts and the disks themselves. those calipers went on my old 90 n/a. bloody good them brakes were after a full service/overhaul.

G
 
so i should sell that spacer kit i took out of those calipers i got off you disco? :) i was hanging onto them incase i wanted to do my 300tdi calipers and just buy the disks. so vented and drilled are no better than solid?

G

Unless you're constantly overheating the brakes then solids are fine, best and cheapest way to improve brake power is to machine 5/10mm off the bottom of the pad surface on all the pads, don't take it off the top as it has the reverse effect! ;)
 
take 5-10 off so that the pad tapers down?

wouldnt say i constantly overheat my 90 but it will be fully loaded for a trip to Morocco in October, would vented help then?

G
 
take 5-10 off so that the pad tapers down?

wouldnt say i constantly overheat my 90 but it will be fully loaded for a trip to Morocco in October, would vented help then?

G

TBH i've never had my brakes overheat nor have i herd of it happening, as mentioned previously in this topic, to get a nice feel on the brake pedal just re-bleed the whole brake system.

I've had the back of the 110 filled with engine's, wheels etc and towed a trailer weighing just over 2tonne at the same time and my solid discs worked fine for me all the way from newcastle to birmingham.:)
 
Another cheap way to get solid discs better cooling properties is to drill a few holes on the face of the disc making sure that the diameter of the holes you're drilling is not greater than the thickness of the actual disc. That way you are increasing the overall surface areas of the disc giving better heat distribution. ;)

But i would say you need to do that
 
Fit braided hoses! The way forwards, I am honestly amazed at the difference it has made to my 90, with drums on the back!

I've only ever had my brakes overheat once, on my 90 shortly after i bought it.

Fully loaded, got to 70 down a hill then emergency stop for the roundabout to test the brakes, the fluid boiled. Changed the fluid, and what came out was a horrible dark brown. Did the same manouver again, brakes work fine and havn't overheated yet.
 
Another cheap way to get solid discs better cooling properties is to drill a few holes on the face of the disc making sure that the diameter of the holes you're drilling is not greater than the thickness of the actual disc. That way you are increasing the overall surface areas of the disc giving better heat distribution. ;)

But i would say you need to do that


I meant to say "but i WOULDN'T say you need to do that" :)
 
:D Cheers guys for the responses, reason why i ask is that im rebuilding my axles and wondered if it was the best way to go? but as bodey1989 says I'll overhaul the breaks. (going to get expensive) :rolleyes:
 

Similar threads