GINGE

GINGE

Greenlane liker, bobble hat hater
Events Planner
Anyone have a link to where i can buy a cat replacement pipe WITH a cherry bomb for a TD5 defender?

Me current setup is straight through with no boxes and a side exit and its just a bit too loud.

I had seen one on the alivetuning site but there not there anymore.

And i have tried google before anyone says! :doh:

Oh and fanks :D
 
I've a stainless steel cherry bomb for td5 it was fitted for 3 months will look in garage and have a look for it would be looking for about £70 for it
 
harlequin said:
BGB These are the boys who made mine. Give them a bell.LAND ROVER DEFENDER 90 STAINLESS STEEL PERFORMANCE EXHAUST BACK BOX | eBay
Click to expand...

Nice one Gary, will call them tomorrow :)

Dr_evil said:
I've got a cherry bomb pipe sat on my shelf, proper one from the states if you want
Click to expand...

Is it to fit a fender 90 though Doc? or is it for your disco? Just want an off the shelf piece to be honest. no welding or fabrication for me. :lol:

redwingslandrover said:
Bought it from friend that had it on his for 3 months I had it as I was going to buy td5 but ended up with 300 tdi
Click to expand...

Ok, thanks. Will have a look and see if its worth it for me with the postage. it might prove to be cheaper for me to get a new one locally made.

Thanks again. :)
 
I just used some putty and a standard 2.5" sleeve clamp :) if you're running a 2.5" pipe atm it'll fit right on
 
Will require a little angle grinding or a few extra seconds with a hack saw, basically remove the flange on either pipe (will need about a foot removed all in so 6" either side)

Get two exhaust clamps (one as it comes with one) and pop it in there, no welding, keeps the over axle part too and very solid! I drove it through a few floods and the rubber mount broke instead of the putty/clamp combo so tough enough
 
Dr_evil said:
Will require a little angle grinding or a few extra seconds with a hack saw, basically remove the flange on either pipe (will need about a foot removed all in so 6" either side)

Get two exhaust clamps (one as it comes with one) and pop it in there, no welding, keeps the over axle part too and very solid! I drove it through a few floods and the rubber mount broke instead of the putty/clamp combo so tough enough
Click to expand...

are you getting rid of it because your present motor is quiet without it :behindsofa:
 
No thats got a cherry bomb on it too ;) and only on 1.75 pipe rather than 2.5 cos petrol needs something more restrictive than derv if its not turbo'd
 
Thanks Doc, but ill give it a miss. :)

I have flanges on the down pipe and the rear section so would mean cutting those off etc etc. Ill just buy one ready to go.

Thanks again.
 
it int me im worried about. :lol: me new place is a grove full of old biddies. :( they int very happy i tell ya! oops :(
 
You must log in or register to reply here.

Similar threads

JokerUK
L320 Fuel Rail question
Replies
6
Views
872
Datatek
Datatek
R
Where is that bloody water coming from in the footwell?
Replies
2
Views
811
Ratten
R
richhemmings
Freelander 2 (LR2) Service and Maintenance Tracker
Replies
3
Views
904
richhemmings
richhemmings
J
300 Tdi engine swap story - and a few questions
Replies
13
Views
2K
doriz
doriz
J
300 Tdi Engine back in, nearly - Story and at the end Questions
Replies
0
Views
599
jer_300Tdi_90
J