D

Discokev300

New Member
Hi guys i have a 300tdi disco, i recently changed my injection pump, but like a fool i never timed the car up before removing it so after refitting the new pump i had to time the whole engine up crank and cam are bang on the marks, i got the pump timed up with a locating pin through the pulley fitted new belt tensioner and idler, all back together but i cant get it to run right it struggles to start when cold its got a bad diesel knock and is down on power. Can anybody put me right where have i gone wrong PLEASE HELP it driving me crazy thanks in advance
 
Yes i have stripped it down 3 times now to check 1 thing though i cant get a pin in the flywheel when its inline the cank is about 40 degrees out so just time it with the crank keyway at 12 o,clock
 
key has to be at 12 and flywheels have more than one slot, 300 is smaller dia than previous slots that are there on the flywheel
 
Discokev300 said:
Yeah its nowhere near when the pin drops in your at about 4 o,clock
Click to expand...
By way of confirmation, remove the rocker cover and check the rocker/valve position on cylinder number one when you think the timing marks are indicating TDC, both valves should be closed on the rise of the piston. Further confirmation can be had by removing the injector from cylinder number one and using a thin rod down the hole to gauge the rise of the piston to TDC on compression. That is the true crank position to set the pump to, so if after you've done that and the pump setting pin won't go in, your crank keyway or flywheel timing slot is out for some reason. But if you set the pump to that it should run ok.
It's Interesting that the keyway and flywheel slot are out of phase, not sure if the flywheel mounting to crank is angular movable on this engine, as far as I can figure this is the only way those two indicators could be out.
 
The car actually ran fine until i replaced the injector pump my mistake was removing the cambelt and pump and pulley thinking i could time it up on refit but thats where my problems lay i have had it running for a few weeks but its just not right at all
 
I changed the pump because i was losing fuel at the throttle shaft and the car was cutting out periodically but later found a stone in the fuel line which was restricting the fuel supply
 
Discokev300 said:
I changed the pump because i was losing fuel at the throttle shaft and the car was cutting out periodically but later found a stone in the fuel line which was restricting the fuel supply
Click to expand...
Both common leakage points on the Bosch VE pump can be fixed with the IP in place on the engine, (throttle shaft and discharge head), the latter being a bit of a fiddle but certainly achievable.
There is a "point of injection" (POI), figure for the pump, that is a stroke measurement of the pump related to TDC of the engine but a dial indicator and special adaptor is required for the job, if the POI setting is incorrect the engine will not run well. That position can only be lost if the drive pulley adaptor is removed from the IP shaft.
There is no need to alter any "as found" settings of the pump to replace "O" rings on the throttle shaft or discharge head.
 
You must log in or register to reply here.

Similar threads

Lex Myster
Freelander 2 TD4 Timing Belt
Replies
4
Views
619
Stanleysteamer
Stanleysteamer
Maat
Disco 1 300tdi diesel leak
Replies
11
Views
344
Maat
Maat
C
2.5 Petrol Timing
Replies
4
Views
461
styleruk
styleruk
MAF Diver
Disco 2 Unknown coolant leak at the front onto the oil filter and diff
Replies
0
Views
233
MAF Diver
MAF Diver
tweedandbriar
Is this battery or fuel pump...or what?
2
Replies
24
Views
918
sierrafery
sierrafery