Galen

Galen

New Member
Hello everyone,

I have a brake pedal that likes to creep...

Stamp on the pedal a few times to make it hard (fnarr) and then keep pressure on the pedal and it seems fine. Doesn't appear to creep at all.

Star the engine and perform the same test and the pedal creeps all the way to the floor in around 7 seconds.

There are no obvious leaks anywhere and the brake fluid doesn't appear to be discoloured.

Is this caused by aged fluid or is there a more sinister reason behind it?

Galen
 
check yer master cylinder
get someone to pump the pedal while you look inside the reservoir, if yer see bubbles come up its fooked
 
Would bubbles mean the fluid is fooked or the master cylinder is fooked?

I'm off to check for bubbles....

Galen

Edit: No bubbles observed.
 
did you try watching while the pedal went to the floor?

if you see bubbles yer cylinder is goosed.

if you have no fluid leaks and yer pedal is going all the way down then either yer low on fluid or yer cylinder is goosed
 
slob said:
did you try watching while the pedal went to the floor?
Click to expand...
Allegedly, but wifey was operating the pedal and they never lie...
I'll stamp on it myself tomorrow and let her take a look see.

slob said:
if you see bubbles yer cylinder is goosed.

if you have no fluid leaks and yer pedal is going all the way down then either yer low on fluid or yer cylinder is goosed
Click to expand...

No obvious leaks. The fluid level is pretty much up to the max mark and hasn't been topped up for a while.
Time to price up the brake cylinder I suppose, or a repair kit if they're available.

Thanks for your info slob.

Galen
 
So let me get this right, when engine is off you can pump the pedal and it goes hard, start the engine so the vacumn kicks in and the pedal will initially pump to be hard then eventually it creeps down to the floor almost?
Im not questionin sir slobs theory but, most cars ive driven tend to do this when started, by all means be sure to check everythin regardin the brake system coz you dont mess where brakes are concerned, but also check against other vehicle of same type to see if it does the same.
Like i said not callin anyone into question but just to double check before jumpin in and spendin hard earned.
 
landy10 said:
So let me get this right, when engine is off you can pump the pedal and it goes hard, start the engine so the vacumn kicks in and the pedal will initially pump to be hard then eventually it creeps down to the floor almost?
Click to expand...

That's pretty much it. It takes around 7 seconds to drop to the floor.
Once it's done that if you pump it twice it's rock solid again for another 7 seconds.

landy10 said:
Im not questionin sir slobs theory but, most cars ive driven tend to do this when started, by all means be sure to check everythin regardin the brake system coz you dont mess where brakes are concerned, but also check against other vehicle of same type to see if it does the same.
Click to expand...

I'd expect the vacuum assist to drag the pedal down upon starting the engine, but i'd also expect it to stop at some point and hold; not drop to the floor.

landy10 said:
Like i said not callin anyone into question but just to double check before jumpin in and spendin hard earned.
Click to expand...

I'll take all and any advice because I have no idea what the problem is. Hence asking the knowledgeable folks here :)

Galen
 
Have you not considered the brake booster, especially since it only goes to the floor after you start the engine,

Ray
 
Springbok said:
Have you not considered the brake booster, especially since it only goes to the floor after you start the engine,
Click to expand...

If the booster was leaking i'd expect the vacuum assist to fade and resistance to return?

I've never had a unit fail so i've no idea what the result would be.:eek:

Galen
 
Hi,

If it is your master cylinder , dont do wwot I did on my clutch master replaced the rubbers twice and then bought after market new and all was well. good luck.

Ray
 
At the moment i'm leaning toward replacing the fluid and seeing if that makes things better or worse. It's a cheap option and no big deal if it doesn't make any difference.

If new fluid doesn't make a difference it'll probably be a replacement cylinder and/or vacuum servo I guess.

Galen
 
Update:

Flushed the brake fluid today the brakes are more positive, but still have the same 'feature' albeit a little slower.

I did come across this though Brake Parts for Cars

I also spotted that the bloody r380 filler plug is weeping. That's tomorrows job I suppose.

BTW what's with the plastic filler plugs in the axles?

Galen
 
if he hadn't sed it wint all the way to the floor ah would have sed "they all do that"
as fer doosul brake creep thats a new un on me, and i have me doubts about how accyreet it is.
but then ave only every own one doosul though i have driven a few and worked on a shed load of em and ave nevva heard of it.


someone should do a poll to see how many have heard of doosul creep
 
so ave read this doosul creep thing again and according to that it only happens when yer int moving. so if int dunt do it when yer moving, then thats looks like yer problem. if it does yer back to yer master cylinder
 
slob said:
so ave read this doosul creep thing again and according to that it only happens when yer int moving. so if int dunt do it when yer moving, then thats looks like yer problem. if it does yer back to yer master cylinder
Click to expand...

I can't say i've noticed it happening when i'm moving, but will keep an eye on it.
 
Galen said:
Update:

Flushed the brake fluid today the brakes are more positive, but still have the same 'feature' albeit a little slower.

I did come across this though Brake Parts for Cars

I also spotted that the bloody r380 filler plug is weeping. That's tomorrows job I suppose.

BTW what's with the plastic filler plugs in the axles?

Galen
Click to expand...

Hi Galen,

You can replace the plastic axle filler plugs with these https://www.jgs4x4.co.uk/discovery-2-heavy-duty-brass-differential-filler-plugs/
Much better....
 
You must log in or register to reply here.

Similar threads

L
Disco 2 brake question
Replies
5
Views
640
landynutterme
L
P
Discovery 2 brake issues after replacment
Replies
4
Views
725
psk100
P
Z
P38A Random braking problem-sometimes extremely hard brake pedal
Replies
19
Views
1K
Datatek
Datatek
S
Freelander 2 (LR2) Brake Pedal Cruise Control Switch
Replies
0
Views
248
Stevelander 2
S
W
Brakes require pumping!
Replies
9
Views
688
Anaconda
A