Pete_TD4

Member
Hi guys,

Thanks for your help with the VCU-change advice last week - that's all sorted, but now I have a new problem :-(

For the last couple of months I've noticed the car taking a bit longer to start, but nothing too drastic. Then over the last few days it has ceased to start at all. Not a battery problem, it turns over strongly, but doesn't fire.

The glow-plug light on the dash lights for the normal amount of time, then goes out. The wheel-arch fuel pump is whirring away as normal.

I found mention of the "injector leak test" as described here, but couldn't see any diesel rising in the tops of the injectors. My first attempt at clamping the disconnected hose wasn't very successful, resulting in diesel flowing pretty freely out of the T-pieces - I don't know whether that's normal or significant?

I've been able to get it going a couple of times using Easy-Start (which obviously I dislike doing). Once running, it runs smoothly. There's a little white smoke/vapour in the exhaust, but that could be normal for a cold morning, I don't normally look. Certainly nothing excessive. If stopped, it will restart ok at least within the next hour.

I need the car to get to work, so after the injector test came up with nothing I decided it was time to take it to a garage. However, my local LR specialist is always booked up for weeks in advance, and the diesel place someone recommended also can't look at it for at least seven days. Hence the mention of Southampton (home) and Fareham (work) in the subject - perhaps any local LZers can recommend a place?

In the meantime, any other suggestions for things to try are welcome.

Thanks,

Pete
 
Last edited:
Could also be a leak back, causing an unequal pressure across the 4 injectors, causing it to fail to start ...
 
Thanks - but a couple of things there don't quite match:
1. It says worse when hot, whereas mine is the opposite. Once the engine is warm, it starts ok.
2. It talks about the engine stopping once the EasyStart is consumed, whereas mine keeps going.

Are these essential characteristics of a camshaft fault?

Pete

Did you read all of the thread ?
 
Depends on what you did....

"Remove engine cover to access the injectors. The small bore flexi pipes that link across the injector tops are the "leak off" or "spill pipes" that return fuel back to the tank when the engine is running. BUT with the ignition on but engine NOT started the low pressure fuel pump/s build up pressure in the injectors and NO fuel should be returning via these pipes.
Prepare to test; pull out the spring clip which secures the "T" piece on each injector and carefully lift out each plastic "T". Don't try to pull the pipes from the T because they will snap off and are difficult to come by. With all four disconnected clamp the pipe before the first T piece where it comes up in front of the engine to prevent fuel coming back up the pipe from other locations.
To test simply turn on the ignition (don't start) and check for fuel emitting from the injector tops. Any that leak need to be replaced as this is where fuel pressure required for initial starting is being lost."
 
Did you read all of the thread ?
I skipped the EGR stuff, I already have mine bypassed. But his testing of the camshaft sensor involved freezing it to make it work, whereas in a warm engine it did not. Mine is the other way round, it works when the engine's warm but not when it's cold.

Pete
 
Yep, those are the exact instructions I linked to ;)

Pete

In that case it's probably a good idea to start saving up for a set of re-con injectors ... sorry mate ... I'm sure a grown up will be along soon to answer your query properly ...
 
Could it just be glow plugs? Don't if there's a warning light for failure but the light on the dash normally just means a supply is going to the plugs, not that the plugs are actually working.
 
In that case it's probably a good idea to start saving up for a set of re-con injectors
So we think the injectors might be faulty in a different way to what the leak-off test shows up?
I've seen some "re-con" injectors on eBay for pretty good prices - but maybe the only reconditioning they got was a quick wash...?

Pete
 
Could it just be glow plugs? Don't if there's a warning light for failure but the light on the dash normally just means a supply is going to the plugs, not that the plugs are actually working.
It's a thought. I wonder if there's a way to put a multimeter on the circuit and see what current it's pulling? Unfortunately I don't have a clamp meter I can just put round a wire...

Pete
 
I have no knowledge of freelanders (as you may be able to tell) but on other motors you can pull the plugs then connect them across a battery to check that they get redhot. (If you try that, do not hold them by the hot end)
 
Check the HPFP regulator as sometime the O-rings can wear thus you get low pressure, fix is about £5.99 and about an hour of your own time to rectify.

Thanks - I'll have a look if I can't get it into a garage right away (at the moment the priority is getting a working car one way or the other). Is it hard to get to?

it could even be the fue pump is not working as it should, fuel filter, when were these last checked or changed,

The low pressure pump died about three years ago. I replaced it with a cheap pattern part, which I kind of regret as it's pretty noisy, but I don't think that's the problem here. It sounds no different to usual, and the diesel ****ing out of the leak-off hose when I didn't clamp it hard enough shows that plenty of fuel is reaching the engine.
The car got a service from a trustworthy LR specialist maybe 18 months ago; I assume they changed any filter that needed changing. The sedimenter under the wheel arch looked pretty clean back when I changed the pump.
If there was a fuel supply problem I'd expect to see some effect when driving, but once started it runs smoothly and accelerates up to motorway speed exactly as normal. It's only a starting problem.

Pete
 
Changing the O-rings is not to hard, takes about an hour removed the starter motor first, then you get access to the two torx bolts remove these and the regulator will come away check and change the O-rings even if they look ok as they will go sooner or later, while you are at it clean the starter motor contact single wire connector you could even do that first see what happens.
 
Thanks - I'll have a look if I can't get it into a garage right away (at the moment the priority is getting a working car one way or the other). Is it hard to get to?



The low pressure pump died about three years ago. I replaced it with a cheap pattern part, which I kind of regret as it's pretty noisy, but I don't think that's the problem here. It sounds no different to usual, and the diesel ****ing out of the leak-off hose when I didn't clamp it hard enough shows that plenty of fuel is reaching the engine.
The car got a service from a trustworthy LR specialist maybe 18 months ago; I assume they changed any filter that needed changing. The sedimenter under the wheel arch looked pretty clean back when I changed the pump.
If there was a fuel supply problem I'd expect to see some effect when driving, but once started it runs smoothly and accelerates up to motorway speed exactly as normal. It's only a starting problem.

Pete
"Diesel ****ing out... plenty of fuel is reaching the engine" - this is good common sense diagnostics, but remember this isn't a rotary-pump Perkins - the Td4 has quite a complex fuelling and injection set-up. If you're not getting good pump pressure (upwards of 350 kPa) then you'll get exactly the symptoms you describe. The on-road performance may start to suffer later.

A cheap, noisy three year-old LP pump would be my first point of suspicion here. Also, a cranking leakback test on the injectors would be more revealing.

Check the glowplug resistances - measure ohms from terminal to earth. My new ones read about 1 ohm. Also check voltage present during key on.

As said, the HP regulator O-ring is worth replacing.
 
good common sense diagnostics, but remember this isn't a rotary-pump Perkins
Heh, guilty as charged - I'm mostly a boat guy, not cars, and old-fashioned Perkins lumps are quite common boat engines :)
Also, a cranking leakback test on the injectors would be more revealing.
Ok - so disconnect the return hoses as before, but this time crank the engine instead of just turning on the power?
I'm not going to be able to watch them as I actually turn the key, presumably ok to quickly look afterwards and see if any have filled up?
Check the glowplug resistances - measure ohms from terminal to earth. My new ones read about 1 ohm. Also check voltage present during key on. As said, the HP regulator O-ring is worth replacing.
Thanks for a few more things to look at. I've just driven out from the office to lunch and back, and since it's fairly warm here today and the engine might still have been warm from the drive in, it didn't light the lamp to ask for glow plugs. It then started immediately on turning the key. This tends to make me think the glow plugs are the problem - though maybe that's just wishful thinking since they seem easy to fix :)

Pete
 
On cranking, they'll all leak back. Point is to measure how equal they are - if one is hogging fuel pressure, starting may become difficult as the whole rail pressure will be too low. Have a search on here for leakback test - the principle is the same but you need to attach pipes to the injector spill spigots and feed these to four measuring cylinders or syringes.

Regarding glow plugs, they are certainly worth a check but unless conditions are extreme a modern engine such as the Td4 will still start. I bought our FL with only one working glow plug and it still started in freezing conditions. A bit farty and smoky, but it started.

If you must remove the glow plugs, soak them well in WD40 first and use a 1/4" ratchet so you can't apply too much torque. They break off for a pastime. Turn them very gradually, going forwards and backwards and reapplying WD40 regularly.
 

Similar threads