MJI · Jan 17, 2015

Went for a drive in the snow, was difficult to engage CDL, and I really had to pull hard to get it out of unlock.

A month ago it was fine.

What do I need to check please?

beerdude · Jan 17, 2015

You have a centre diff lock on a Disco 2?
On the Disco 1 you need to remove the console, drill out the rivets holding down the cover plate and gaiter, then you can remove the pin being careful not to lose the clip, undo 4 bolts (8mm heads on 6mm thread I think) then you can lift out the assembly, take it in the warm and soak in penetrating oil and tap it until it frees up, lube it up and rebuild it. really not a terrible job.
Good Luck Kev

MJI · Jan 17, 2015

beerdude said:
You have a centre diff lock on a Disco 2?
On the Disco 1 you need to remove the console, drill out the rivets holding down the cover plate and gaiter, then you can remove the pin being careful not to lose the clip, undo 4 bolts (8mm heads on 6mm thread I think) then you can lift out the assembly, take it in the warm and soak in penetrating oil and tap it until it frees up, lube it up and rebuild it. really not a terrible job.
Good Luck Kev

Thanks

Of course it has CDL, why would it not?

I think mine is cable where yours is lever, but will have a look when it is warmer.

Just very stiff!

thebiglad · Jan 17, 2015

MJI said:
Thanks

Of course it has CDL, why would it not?

I think mine is cable where yours is lever, but will have a look when it is warmer.

Just very stiff!

Because on Facelift D2's (like the one in your avatar) they rarely have CDL, let alone one with the correct linkage.

Dave

MJI · Jan 17, 2015

thebiglad said:
Because on Facelift D2's (like the one in your avatar) they rarely have CDL, let alone one with the correct linkage.

Dave

Fair enough, but what tends to stick?

50 pence · Jan 17, 2015

MJI said:
Fair enough, but what tends to stick?

My money is on the cable. I have seen many high/low cables seize and the cdl cable is the same design.
Get under and get some wd40 on it and work it side to side. Make sure you spray the clevis and pins each end as well.

thebiglad · Jan 17, 2015

WD-40 is NOT a lubricant, it's a Water Dispersant. The cables need oil or grease to keep them working properly.

If cable replacement is required, give the inner a good oiling/greasing before fitting it.

beerdude · Jan 17, 2015

Disc 2 has a cable high/low control which I have known to be problematic through lack of use and the Disco 1 is lever operated. I have never seen a D2 with factory diff lock though

discool · Jan 17, 2015

Standard on some later models and option on the others according to my sales brochures.

beerdude · Jan 17, 2015

I learned something new today then and as I think you should do something that scares you and learn something new every day I'm half way there today

MJI · Jan 17, 2015

The display lights up and the TC changes it sensitivity, a LOT better on mud than not engaged.

Thomo1927 · Jan 17, 2015

I try to use my D/L once a week , just to keep everything working on my 300.

YK55 · Jan 20, 2015

My high/low range cable has just snapped and I need a new one. Can they be fitted from underneath or does the console need to come out?

(50 pence, I've tried sending you a message but nothings showing in my sent box.)

darrenm · Jan 20, 2015

My 2004 sometimes is difficult but I think it's because of lack of use

discool · Jan 20, 2015

darrenm said:
My 2004 sometimes is difficult but I think it's because of lack of use

Not lack of use but lack of lubrication

MJI

Well-Known Member

beerdude

Active Member

MJI

Well-Known Member

thebiglad

Well-Known Member

MJI

Well-Known Member

50 pence

New Member

thebiglad

Well-Known Member

beerdude

Active Member

discool

Well-Known Member

beerdude

Active Member

MJI

Well-Known Member

Thomo1927

Active Member

YK55

New Member

darrenm

Active Member

discool

Well-Known Member

Similar threads