dunkan · Aug 29, 2014

Collected all the shot blasting yesterday and its now getting a coat of zinc primer followed by Black top coat

Bumpers are at the powder coaters and will be satin Black

I'm attacking the chassis today removing old flaky paint and surface corrosion

dunkan · Aug 29, 2014

Lots of painting done and in the process of being done, chassis is
getting there but needs another day on it.

Tailgate looking quite poorly but a new skin will see that looking
like new again

Exhaust Y piece cleaned up really well, no holes or weak patches
which was great news.

Manifolds also looking good but have 2 broken studs in one side
that i have to attack, hopefully i can borrow a Bridgeport turret
mill to get them out nicely

dunkan · Sep 1, 2014

Decided to remove the chassis from the body and do a proper job.

After the new body panels have been fitted, rear cross member, sills, inner
front wings & arch's etc the body will come off the chassis and stripped down,
then it's off to be acid stripped and galvanized

Rustystuff · Sep 1, 2014

Subscribing to this one... great job so far ! If only I could pull mine of the road for this sort of treatment..... Looks like your in the right place to get the work done !
Great motors... every one worth saving. Good job keep it up.

dunkan · Sep 2, 2014

Rustystuff said:
Subscribing to this one... great job so far ! If only I could pull mine of the road for this sort of treatment..... Looks like your in the right place to get the work done !
Great motors... every one worth saving. Good job keep it up.

Cheers mate.

Hopefully it wont be long before the bodies off the chassis, we have to get all the new panels in first as the chassis is acting as the jig to hold the body in the right place.

dunkan · Sep 3, 2014

A few pics of the front end

Found a better VHT paint that stays Black

Got the broken studs out the manifolds and then re painted with Simonize VHT paint, good for 800 C according
to the tin

dunkan · Sep 4, 2014

New rear cross member is fitted and the boot floor is pretty much finished,
when the shells painted the new aluminium floor panel will be riveted in place, obviously
after we start rebuilding it

kingdem · Sep 5, 2014

Nice job.

dunkan · Sep 5, 2014

kingdem said:
Nice job.

Thanks

3.5 efi · Sep 5, 2014

That'll be a fine motor car when it's finished.

dunkan · Sep 5, 2014

3.5 efi said:
That'll be a fine motor car when it's finished.

Cheers, yes i think it should be pretty good when we're done.

dunkan · Sep 9, 2014

New parts arrived today

dunkan · Sep 10, 2014

Near side sill is finished and work has started on the n/s front wing, wheel
arch, inner wing and headlamp box.

dunkan · Sep 11, 2014

Nearside inner wing, wheel arch and headlamp box being fitted now.

Front seats are out in preparation to lift the body off the chassis.

Front axle being assembled with new diff, cv's and swivel housings

dunkan · Sep 15, 2014

Offside almost ready for new panels and the tailgate with the bottom panel removed and a bit of surface rust to deal with

dunkan · Sep 16, 2014

New panels now fitted to the offside, just the inner and outer sills to do and then drop the chassis out from under the body

Druim · Sep 16, 2014

Hell of a project, you must be in love

dunkan · Sep 16, 2014

Druim said:
Hell of a project, you must be in love

Thanks Druim, i hope its worth it in the end but should be like new by the time we're finished

ukadamwest · Sep 16, 2014

while the front is off are you going put a performance cam in or is the engine coming out too ?

dunkan · Sep 16, 2014

ukadamwest said:
while the front is off are you going put a performance cam in or is the engine coming out too ?

Once the inner and outer offside sills are replaced the chassis will be dropped off from the body and the engine, box etc then taken off the chassis.

I'm not sure what to do with the engine as it runs very nicely and
compression tests are very good but its done 126,000 miles.

Possibly looking at getting it either rebuilt by John Eales or buy a new engine from him.

Active Member

Attachments

Active Member

Attachments

Active Member

Active Member

Active Member

Active Member

Attachments

Active Member

Attachments

New Member

Active Member

Well-Known Member

Active Member

Active Member

Attachments

Active Member

Attachments

Active Member

Attachments

Active Member

Attachments

Active Member

Attachments

Well-Known Member

Active Member

Well-Known Member

Active Member

Similar threads