P

Phil Maddox

Member
Hi all. Purchased a drop arm puller for my 1980 series 3, but its too big . Its the "24mm" one which i thought would fit. Not sure what the 24mm refers to? After searching further i see there are "19mm" versions available. Is that what i need ?
All help / input appreciatted
Cheers
Phil
PXL_20240225_105633029.jpg
PXL_20240225_105659516.jpg
 
Does the 24mm represent the gap on the jaws of the puller?
If so then measure the gap you need and if it's 19mm then Bob's ur Uncle.
 
The one I linked to has a jaw gap just under 43mm.
Think you have a Defender one.
Give them an email and see what they say. They make the stuff themselves and are proper Series Land Rover enthusiasts.
 
steve2286w said:
Can you return it for exchange or put a couple of bolts either side sitting on the lugs and jamming on the drop arm
Click to expand...
I think i can still return it. Ive asked the seller if he has a smaller version. Ill report back my findings when he has responded. Failing which the bolt idea might be worth a try. Thanks
 
Anaconda said:
Did you get it sorted?
Click to expand...
No not yet. Im still in the process of dismantling the whole vehicle so when the weathers good Im outside working on removing everything from the old chassis.
I did order a "19 mm drop arm puller" but it had an even wider opening ( 57.5mm) so i returned it.
So I'm not sure which puller to order, added to which all the ones that claim to be for a Series 3 are upwards of 50 pounds which seems a tad expensive for something I'll only need once ( hopefully)
 
Phil Maddox said:
No not yet. Im still in the process of dismantling the whole vehicle so when the weathers good Im outside working on removing everything from the old chassis.
I did order a "19 mm drop arm puller" but it had an even wider opening ( 57.5mm) so i returned it.
So I'm not sure which puller to order, added to which all the ones that claim to be for a Series 3 are upwards of 50 pounds which seems a tad expensive for something I'll only need once ( hopefully)
Click to expand...

If you put up a rough location, someone might lend you a puller ...
 
Dippypud said:
Take a piccy alongside the measuring stick ...
Click to expand...
So here's what i have . Looks like a standard LR S3 arrangement but i have no reference to gauge by.
Splined shaft is 25.2 ( me thinks 1 inch then)
To fit under " the ears" a puller would need an opening of 42mm.
Judging by the state of the lock washer its been off before but to me, it doesn't look like its on far enough ( see pic showing 10.3mm between drop arm and steering box)
PXL_20240304_153721903.jpg
PXL_20240304_153805535.jpg
PXL_20240304_153842459.jpg
PXL_20240304_153903825.jpg
 
This is the adapter I made.
 

Attachments

  • IMG_20240304_185633.jpg
    IMG_20240304_185633.jpg
    236.4 KB · Views: 87
  • IMG_20240304_185707.jpg
    IMG_20240304_185707.jpg
    307.9 KB · Views: 87
  • IMG_20240304_185657.jpg
    IMG_20240304_185657.jpg
    342.3 KB · Views: 71
You must log in or register to reply here.

Similar threads

dag019
Drop arm ball joint puller
2
Replies
32
Views
4K
KISSMYAURA
KISSMYAURA
D
Which Drop Arm Puller ?
Replies
10
Views
2K
tottot
tottot
G
Coolant temperature sender Series 3 2.25 diesel question.
Replies
5
Views
1K
Guidoma
G
Hellastony
LHD Series 3 throttle linkage question...
Replies
6
Views
2K
Hellastony
Hellastony
T
Adding rear seats to my Series 3 88"
Replies
17
Views
3K
300bhp/ton
300bhp/ton