flash42

flash42

Active Member
been getting the 90 ready for its retest today and got a new nozzle for the washer jet. but it just wouldnt go on, and in the end it broke due to a bit to much force.
gonna get a new one from brookwells tomorrow.
but before we break another can anyone tell me how the bloody thing goes on?

cheers

flash
 
flash42 said:
been getting the 90 ready for its retest today and got a new nozzle for the washer jet. but it just wouldnt go on, and in the end it broke due to a bit to much force.
gonna get a new one from brookwells tomorrow.
but before we break another can anyone tell me how the bloody thing goes on?

cheers

flash
Click to expand...


hahahahaha. Snap did the same my self on tuesday. I think they just get brittle with age. I'll be putting a bit of vaseline or similar on mine before I shove it in. :eek: On the plus side once you get past 30mph the wind/slipstream just sprays it straight back on to the windscreen anyway :D :D
 
redhand said:
hahahahaha. Snap did the same my self on tuesday. I think they just get brittle with age. I'll be putting a bit of vaseline or similar on mine before I shove it in. :eek: On the plus side once you get past 30mph the wind/slipstream just sprays it straight back on to the windscreen anyway :D :D
Click to expand...

might be a bit of a problem getting it upto 30mph in the mot test bay tho:)
 
thats why i need to get it on, bloody MOT man. :(
anyone else got any ideas?
also how much do u reckon brookwells are gonna rip me off for?
 
Not quite sure wot ur trying to do but if its wot I think ur trying to do, soften the pipe with hot/boiling water. Alternatively u could ask the missus how her mother is n hold the pipe in front of her like a microphone..........
 
mysteryman said:
Not quite sure wot ur trying to do but if its wot I think ur trying to do, soften the pipe with hot/boiling water. Alternatively u could ask the missus how her mother is n hold the pipe in front of her like a microphone..........
Click to expand...


The new bit should be much more flexible and therefor a spot of vaseline and a twisting motion will get it on no problem.


alternatively you go down the path of the pug 405's and have a length of tubing attached to the wiper arm and plumb that to the washer pump and drill small holes in the pipe where it clips to the wipers. I think Trewy has a thread on here somewhere.
 
6.jpg
 
I did exactly the same thing and seeing as I still have warranty and the weather was bad as far as I was concerned it was off the road so I called Land Rover assistance to deal with it, I thought this'll take two minutes, he'll warm it up or summat, must do loads of em, couldn't believe it when he said I'll have to take the dash out and replace the lot?????? I thought maybe it's not meant to come off but it must do if you can buy it seperately?
 
I put front and rear plastic washer thing on mine a while back after breaking them, the new ones came with the two bits together so I had to unscrew the retaining nut behind the dash and change out the whole thing, I managed to get it by pulling out the ashtray and it is just under there
 
You must log in or register to reply here.

Similar threads

W
300 Tdi glow plug connection: what size is the nut on the electrical connection?
Replies
4
Views
798
Wolf Spider
W
T
Help needed if anyone can help I have the bonnet saying that it’s open I know it’s not.where is the sensor located on a L322 how do I get to it thanks
Replies
2
Views
429
backinblack
backinblack
JIMBOB LR
Less Is More. The LR Series lives on.
2 3
Replies
44
Views
4K
JIMBOB LR
JIMBOB LR
J
300 Tdi Engine back in, nearly - Story and at the end Questions
Replies
0
Views
696
jer_300Tdi_90
J
L
SOLD - Land Rover Ninety (Defender 90) 300TDi Auto soft-top
Replies
9
Views
4K
mondifa
M